Buell XB 2010 Скачать руководство пользователя страница 203 | Manualshive

Страница: 203 / 714

background image

2.27

FAIRING SUPPORT BRACKET: FIREBOLT

REMOVAL

1.

Remove seat.

To prevent accidental vehicle start-up, which could cause
death or serious injury, disconnect negative (-) battery
cable before proceeding. (00048a)

2.

Disconnect battery cables from battery: negative cable
(black) first. See

1.16 BATTERY MAINTENANCE

.

3.

Remove front fairing. See

2.47 FRONT FAIRING, WIND-

SHIELD, AND MIRRORS: FIREBOLT

4.

Remove headlight support bracket. See

ASSEMBLY AND SUPPORT BRACKET

.

5.

Remove fuse block and relay block and p-clamp. See

6.20 MAIN FUSE AND FUSES

.

6.

Disconnect and remove horn. See

.

7.

Disconnect and remove instrument cluster. See

6.25 INSTRUMENT MODULE

8.

See

. Remove fairing support bracket

fasteners and washers (4), p-clamp (7) to remove fairing
support bracket (5).

INSTALLATION

1.

Route the wire harness. See

D.1 APPENDIX D: HOSE

AND WIRE ROUTING

for wire harness routing.

2.

. Install fairing support bracket with

fasteners and washers (4, 8) and p-clamp (7). Tighten to
16-18 ft-lbs (22-26 Nm).

3.

Connect instrument cluster connector and install instru-
ment cluster. Tightening to 12-36 in-lbs (1.4-4 Nm). See

6.25 INSTRUMENT MODULE

.

4.

Install horn and tighten fasteners to 72-96 in-lbs (8-10.8
Nm). See

.

5.

Install fuse block, relay and p-clamp tightening fasteners
to 72-96 in-lbs (8-10.8 Nm). See

6.20 MAIN FUSE AND

6.

Install lower headlight support bracket. See

LAMP ASSEMBLY AND SUPPORT BRACKET

.

7.

Install front fairing. See

2.47 FRONT FAIRING, WIND-

SHIELD, AND MIRRORS: FIREBOLT

.

Connect positive (+) battery cable first. If positive (+) cable
should contact ground with negative (-) cable connected,
the resulting sparks can cause a battery explosion, which
could result in death or serious injury. (00068a)

8.

Connect battery cables to battery: positive cable (red) first.
Tighten to 60-70 in-lbs (6.8-7.9 Nm). See

.

After installing seat, pull upward on seat to be sure it is
locked in position. While riding, a loose seat can shift
causing loss of control, which could result in death or
serious injury. (00070b)

9.

Install seat.

2010 XB Service: Chassis 2-123

«
...
201
202
203
204
205
...
»

Содержание XB 2010











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XB 2010

Бренд: Yamaha Страницы: 124

Stealth Air Cleaner Kit

Бренд: S&S Cycle Страницы: 4

Бренд: Ducati Страницы: 77

Бренд: R&G Страницы: 2

Бренд: Denali Страницы: 5

Бренд: MRA Страницы: 8

Бренд: PUIG Страницы: 2

Бренд: Hudora Страницы: 8

Бренд: Palm Страницы: 14

Бренд: Chicago Electric Страницы: 10

Бренд: Chicago Electric Страницы: 12

Бренд: Chicago Electric Страницы: 12

Бренд: Petzl Страницы: 3

Бренд: Petzl Страницы: 8

Бренд: Petzl Страницы: 17

Бренд: Petzl Страницы: 24

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 87

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды