manualshive.com logo in svg

Buell XB 2010, Руководство по обслуживанию

Сервисный мануал Buell XB 2010 теперь доступен для скачивания бесплатно. Убедитесь, что ваш мотоцикл всегда на ходу благодаря этому надежному руководству. Скачайте его сейчас с manualshive.com и получите всю необходимую информацию для обслуживания вашего мотоцикла.

Поделиться
Скачать
background image

6.12

HORN

REMOVAL

1.

Remove seat.

To prevent accidental vehicle start-up, which could cause
death or serious injury, disconnect negative (-) battery
cable before proceeding. (00048a)

2.

Disconnect negative battery cable.

3.

Access horn:

a.

For Firebolt, remove headlight support bracket. See

2.26 HEADLAMP ASSEMBLY AND SUPPORT
BRACKET

.

b.

For Lightning/Ulysses, remove windscreen. See

2.48 WINDSHIELD AND WINDSCREEN: LIGHTNING
AND ULYSSES MODELS

.

4.

See 

Figure 6-38

 (Firebolt), 

Figure 6-39

 (Lightning) or

Figure 6-40

 (Ulysses). Remove fastener (3).

5.

Remove horn (1) from support bracket (4).

6.

See 

Figure 6-41

. Detach Y/BK power wire and BK ground

wire from terminal clips on horn.

INSTALLATION

1.

See 

Figure 6-41

. Connect Y/BK power wire and BK ground

wire to terminal clips on horn.

2.

See 

Figure 6-38

 (Firebolt), 

Figure 6-39

 (Lightning) or

Figure 6-40

 (Ulysses). Attach horn (1) to support bracket

(4) using fastener (3). Tighten to 72-96 in-lbs (8.1-10.8
Nm).

3.

Install negative battery cable to battery terminal. Tighten
fastener to 60-70 in-lbs (6.8-7.9 Nm).

4.

Check horn operation. If horn does not sound or fails to
function satisfactorily, see 

6.12 HORN, Troubleshooting

.

a.

Turn ignition key switch ON.

b.

Press horn switch to activate horn.

c.

Turn ignition key switch OFF.

5.

For Firebolt, install headlight support bracket and install
front fairing. See 

2.26 HEADLAMP ASSEMBLY AND

SUPPORT BRACKET

.

6.

For Lightning, install windscreen and for Ulysses, install
windscreen/windshield. See 

2.26 HEADLAMP ASSEMBLY

AND SUPPORT BRACKET

.

After installing seat, pull upward on seat to be sure it is
locked in position. While riding, a loose seat can shift
causing loss of control, which could result in death or
serious injury. (00070b)

7.

Install seat.

1

4

2

2

3

sm00443

1.

Horn

2.

Horn connectors [122 A & B]

3.

Horn fastener

4.

Fairing support bracket

Figure 6-38. Horn Assembly: Firebolt (Typical)

4

1

3

2

sm00466

1.

Horn

2.

Horn connectors [122]

3.

Horn fastener

4.

Support bracket

Figure 6-39. Horn Assembly: Lightning

HOME

2010 XB Service: Electrical  6-35

Содержание XB 2010











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XB 2010

Yoshimura 14720BP520 Manual preview
14720BP520
Бренд: Yoshimura Страницы: 7
oset 12.5 Eco Owner'S Manual preview
12.5 Eco
Бренд: oset Страницы: 20
Graphite 56H820 Manual preview
56H820
Бренд: Graphite Страницы: 44
Suzuki GSX 11OOF Service Manual preview
GSX 11OOF
Бренд: Suzuki Страницы: 230
Acewell MD-052-2 Series User Manual preview
MD-052-2 Series
Бренд: Acewell Страницы: 2
Paaschburg & Wunderlich SHIN YO TEXAS Mounting And Safety Instructions preview
SHIN YO TEXAS
Бренд: Paaschburg & Wunderlich Страницы: 2
R&G FI0025BK Fitting Instructions preview
FI0025BK
Бренд: R&G Страницы: 2
Yamaha XV19CSD Owner'S Manual preview
XV19CSD
Бренд: Yamaha Страницы: 96
Yamaha XV17AWZ Owner'S Manual preview
XV17AWZ
Бренд: Yamaha Страницы: 110
Yamaha Tenere 700 2021 Owner'S Manual preview
Tenere 700 2021
Бренд: Yamaha Страницы: 112
Yamaha Tenere 700 2023 Owner'S Manual preview
Tenere 700 2023
Бренд: Yamaha Страницы: 114
Yamaha Super Tenere ES 2023 Owner'S Manual preview
Super Tenere ES 2023
Бренд: Yamaha Страницы: 132
Yamaha Tenere 700 2020 Service Manual preview
Tenere 700 2020
Бренд: Yamaha Страницы: 472
Yamaha XV19CSY Owner'S Manual preview
XV19CSY
Бренд: Yamaha Страницы: 94
Custom Dynamics Magic Strobes Installation Instructions preview
Magic Strobes
Бренд: Custom Dynamics Страницы: 2
Royal Enfield ELECTRA Service Manual preview
ELECTRA
Бренд: Royal Enfield Страницы: 234
X-lite X-801 Operating Instructions Manual preview
X-801
Бренд: X-lite Страницы: 33
DYNATEK D33-1 Installation Instructions preview
D33-1
Бренд: DYNATEK Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды