Buell XB 2010 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 714

background image

WINTER LUBRICATION

In colder climates, the engine oil should be changed often. If
motorcycle is used frequently for short trips, less than 15 mi
(24 km), in ambient temperatures below 60 °F (16 °C), oil
change intervals should be reduced to 1500 mi (2400 km).
Motorcycles used only for short runs must have a thorough
tank flush-out before new oil is put in. The tank flush-out should
be performed by an authorized dealer or qualified technician.

NOTE

The further below freezing the temperature drops, the shorter
the oil change interval should be.

Water vapor is a normal by-product of combustion in any
engine. During cold weather operation, some of the water vapor
condenses to liquid form on the cool metal surfaces inside the
engine. In freezing weather this water will become slush or ice
and, if allowed to accumulate too long, may block the oil lines
and cause damage to the engine.

If the engine is run frequently and allowed to thoroughly warm
up, most of this water will become vapor again and will be
blown out through the crankcase breather.

If the engine is not run frequently and allowed to thoroughly
warm up, this water will accumulate, mix with the engine oil
and form a sludge that is harmful to the engine.

1-8 2010 XB Service: Maintenance

«
...
28
29
30
31
32
...
»

Содержание XB 2010











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XB 2010

Бренд: Yamaha Страницы: 287

Бренд: R&G Страницы: 14

MULTISTRADA 1200S

Бренд: Ducati Страницы: 311

California EV V1100

Бренд: MOTO GUZZI Страницы: 173

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 110

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 216

Бренд: Yamaha Страницы: 380

Бренд: Yamaha Страницы: 658

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 388

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды