Buell XB 2010 Скачать руководство пользователя страница 469 | Manualshive

Страница: 469 / 714

background image

5.17

TRANSMISSION SPROCKET

REMOVAL

TOOL NAME

PART NUMBER

SPROCKET HOLDING TOOL

B-43982

SPROCKET LOCKING TOOL

B-45659

MAINSHAFT LOCKNUT WRENCH

HD-46288

MAINSHAFT LOCKNUT WRENCH

HD-94660-37B

NOTE

Use spacer and fastener from B-45659 to install sprocket
locking tool.

1.

Loosen rear axle pinch fastener.

2.

Unthread axle approximately 15 threads to release tension
from drive belt. See

5.7 DRIVE BELT AND IDLER

.

3.

Remove front sprocket cover. See

4.

. Remove pulley and bracket. See

5.7 DRIVE BELT AND IDLER PULLEY

5.

Inspect pulley by spinning wheel (1) and checking for
excessive wheel bearing wear. See

1.11 DRIVE BELT

MAINTENANCE, Inspection

6.

If pulley wheel needs replacement, remove fastener (6)
and nut (2) from idler pulley bracket (4) and discard.
Replace with new pulley wheel (1).

NOTE

The pulley wheel bearings can not be replaced separately. A
new pulley wheel must be installed.

7.

. Place transmission in first gear. Remove

two socket head screws (1) and lockplate (2).

NOTES

•

Transmission sprocket nut has left-hand threads. Turn nut
clockwise to loosen and remove from main drive gear
shaft.

•

Use the P3/Blast SPROCKET HOLDING TOOL (Part
No. B-43982) with the spacer and fastener from the Fire-
bolt SPROCKET LOCKING TOOL (Part No. B-45659) to
hold the sprocket.

8.

. Place transmission in neutral. Install

the P3/Blast sprocket holding tool (1) to hold the sprocket.

9.

. Remove transmission sprocket nut (3)

from main drive gear (5) using MAINSHAFT LOCKNUT
WRENCH (Part No. HD-94660-37B) or MAINSHAFT
LOCKNUT WRENCH (Part No. HD-46288) and a breaker
bar.

10. Remove secondary drive belt from transmission sprocket.

Remove transmission sprocket (4) from mainshaft (5).

3

1

2

4

5

6

sm00304

1.

Wheel

2.

Wheel nut

3.

Stud (2)

4.

Idler pulley bracket

5.

Idler pulley bracket nut and washer (2)

6.

Wheel fastener

Figure 5-99. Idler Pulley Assembly

5

3

1

4

2

sm00347

1.

Socket head screw (2)

2.

Lockplate

3.

Transmission sprocket nut (left-hand threads)

4.

Transmission sprocket

5.

Main drive gear

Figure 5-100. Transmission Sprocket

2010 XB Service: Drive/Transmission 5-57

«
...
467
468
469
470
471
...
»

Содержание XB 2010











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XB 2010

Бренд: Öhlins Страницы: 8

Nils Extreme MTW03

Бренд: Abisal Страницы: 21

Бренд: klicbag Страницы: 2

Бренд: Yoshimura Страницы: 7

HIGHSIDER VICTORY

Бренд: Paaschburg & Wunderlich Страницы: 5

Бренд: Fantic Motor Страницы: 145

Бренд: Termignoni Страницы: 9

Бренд: KSR Moto Страницы: 51

Бренд: Qingqi Страницы: 48

Бренд: Yadea Страницы: 100

Бренд: Malossi Страницы: 24

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 3

Бренд: Sealey Страницы: 3

Бренд: Sealey Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды