Buell XB 2010 Скачать руководство пользователя страница 542 | Manualshive

Страница: 542 / 714

background image

6.25

INSTRUMENT MODULE

GENERAL

Replace the instrument module if the unit is not working prop-
erly. However, before replacing a component, check that the
problem is not caused by a loose wire connection.

NOTES

•

Replacement bulbs are available for indicator, check
engine light and backlights.

•

Replace instrument module if low fuel warning indicator
fails.

sm03851

Figure 6-82. Instrument Module

REMOVAL

1.

Remove seat.

To prevent accidental vehicle start-up, which could cause
death or serious injury, disconnect negative (-) battery
cable before proceeding. (00048a)

2.

Disconnect negative battery cable.

3.

Access instrument module connector [39]:

a.

For Firebolt, remove headlight support bracket. See

2.26 HEADLAMP ASSEMBLY AND SUPPORT
BRACKET

b.

For Lightning/Ulysses, remove windscreen. See

2.48 WINDSHIELD AND WINDSCREEN: LIGHTNING
AND ULYSSES MODELS

4.

Disconnect instrument module connector [39]:

5.

Remove fasteners and washers.

6.

See

(Lightning) or

(Ulysses). Pull instrument module from support

(1).

Bulb Replacement

1.

Once the instrument module has been removed from the
vehicle place face down on a work surface.

2.

Remove the nine fasteners securing the back of the
module housing to the display and remove back cover.

NOTE

Do not turn display over. The speedometer and tachometer
will fall out possibly causing damage to instruments.

3.

. Insert screwdriver blade into the slot on

the back of the bulb to be replaced and lightly turn coun-
terclockwise and remove bulb.

NOTE

. Bulbs are identified both by color and length.

4.

Select correct replacement bulb and install into back of
instrument cluster.

5.

Reinstall back cover and insert and tighten the nine
fasteners originally removed.

2

3

1

sm00412

1.

Instrument module

2.

Bulbs

3.

Screwdriver

Figure 6-83. Bulb Replacement for Instrument Module

1

2

sm00413

1.

Light gray/taller bulb-Y0162.02A8

2.

Dark gray/shorter bulb-Y0163.02A8

Figure 6-84. Instrument Module Bulbs

6-68 2010 XB Service: Electrical

«
...
540
541
542
543
544
...
»

Содержание XB 2010











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XB 2010

Бренд: R&G Страницы: 6

Rebellion Electric Chopper 15130760

Бренд: Razor Страницы: 17

Бренд: Yamaha Страницы: 130

Бренд: Yamaha Страницы: 102

MSS X9 EVOLUTION 250

Бренд: PIAGGIO Страницы: 262

MP3 500 ie SPORT Business LT 2011

Бренд: PIAGGIO Страницы: 375

Бренд: VESPA Страницы: 249

Spyder RS Series

Бренд: Can-Am Страницы: 37

Бренд: Datatool Страницы: 5

Бренд: Thermo Soles Страницы: 13

FuelGaugePro FGP-SENSOR

Бренд: LSK Страницы: 11

Бренд: RIEJU Страницы: 147

Бренд: Yamaha Страницы: 67

Бренд: Yamaha Страницы: 61

DragStar XVS650A

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 135

Бренд: Yamaha Страницы: 213

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды