Buell XB 2010 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 714

background image

1.16

BATTERY MAINTENANCE

GENERAL

Batteries contain sulfuric acid, which could cause severe
burns to eyes and skin. Wear a protective face shield,
rubberized gloves and protective clothing when working
with batteries. KEEP BATTERIES AWAY FROM CHILDREN.
(00063a)

Never remove warning label attached to top of battery.
Failure to read and understand all precautions contained
in warning, could result in death or serious injury. (00064a)

Batteries, battery posts, terminals and related accessories
contain lead and lead compounds, and other chemicals
known to the State of California to cause cancer, and birth
defects or other reproductive harm. Wash hands after
handling. (00019e)

All AGM batteries are permanently sealed, maintenance-free,
valve-regulated, lead/calcium and sulfuric acid batteries. The
batteries are shipped pre-charged and ready to be put into
service. Do not attempt to open these batteries for any reason.

NOTE

For charging information, see

1.16 BATTERY MAINTENANCE,

Charging Battery

. For testing information, see the electrical

diagnostic manual.

4

1

3

2

sm04816

1.

Warning label

2.

Negative (-) terminal

3.

Positive (+) terminal

4.

Warranty/date code label

Figure 1-44. Battery: XB Models

1

2

3

4

5

6

om00618

4.

1.

Keep flames away

Contents are corrosive

2.

5.

Wear safety glasses

Read instructions

6.

3.

Keep away from children

Contents are explosive

Figure 1-45. Battery Warning Label

2010 XB Service: Maintenance 1-39

«
...
59
60
61
62
63
...
»

Содержание XB 2010











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XB 2010

Бренд: KTM Страницы: 29

Бренд: X-lite Страницы: 84

KTM390-14-01-SL

Бренд: SRC Страницы: 4

Бренд: SHOEI Страницы: 38

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 435

Бренд: Mastech Страницы: 2

Бренд: IBEX Страницы: 3

Бренд: Beta Страницы: 54

Бренд: Abus Страницы: 9

Бренд: Petzl Страницы: 4

Бренд: APRILIA Страницы: 128

Бренд: APRILIA Страницы: 162

Бренд: hepco & becker Страницы: 2

Бренд: APRILIA Страницы: 477

Бренд: KTM Страницы: 22

450 Rally Factory Replica

Бренд: KTM Страницы: 124

Бренд: X-lite Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды