Buderus 800-24 Скачать руководство пользователя страница 39

Страница: 39 / 68

Servicing

Installation and servicing instructions condensing gas boiler 800 - 24/29/43/60 and 800 - 24T25/29T25 H/V • edition 02/2006

Subject to modifications resulting from technical improvements !

Buderus • http://buderus-domestic.co.uk

Code

Meaning

Safety sensor rises faster than 5 °C/sec., blocked for 30 sec.

Possible
cause

Action

Resistance in the installation is too high

Check if not all (thermostatic) radiator valves are closed or
clogged with dirt

Safety sensor is dirty or faulty

Check the safety sensor for dirt. Measure if resistance over
the sensor is correct. If not replace safety sensor by
temporarily with another one (see subsection 5.3.9 and
subsection 5.3.10)

External domestic hot water tank is too small for the
boiler's capacity

Top up the system (see subsection 2.1.1)

Code

Meaning

Temperature difference between the flow and return sensors is too high, blocked for 30 sec.

Possible
cause

Action

Resistance in the installation is too high

Check if not all (thermostatic) radiator valves are closed or
clogged with dirt

Problem with the pump or pump cabling
(no circulation)

Check if the pump cabling is faulty or if the pump is stuck
(see subsection 5.3.7)

Water pressure is too low in the system

Top up the system (see subsection 2.1.1)

Return sensor is defective or the cabling is faulty

Measure the resistance of the sensor
(see subsection 5.3.12)

Code

Meaning

Flow sensor exceeds 100 °C

Possible
cause

Action

Flow sensor is dirty or faulty

Check the sensor, replace if necessary
(see subsection 5.3.9 and subsection 5.3.10)

There is a problem with the pump or pump cabling
(no circulation)

Check if the pump cabling is faulty or if the pump is stuck.
Replace pump if necessary (see subsection 5.3.7 and
subsection 5.3.8)

Water pressure is too low in the installation

Top up the system (see subsection 2.1.1)

Code

Meaning

F2 fuse malfunction, or flue gas thermostat active

Possible
cause

Action

Water pressure is too low in the installation

Top up the system (see subsection 2.1.1)

Heat exchanger is dirty

Check for a dirty heat exchanger and clean if necessary
(see subsection 4.1)

Flue gas retarder faulty or missing

Check if the flue gas retarder is installed in the heat
exchanger

Содержание 800-24





































































Результаты поиска

Содержание 800-24

Отзывы:

Похожие инструкции для 800-24

Бренды по названию

Популярные бренды

Buderus 800-24, Инструкции по установке и обслуживанию

Результаты поиска

Содержание 800-24

Отзывы:

Похожие инструкции для 800-24

Бренды по названию

Популярные бренды