BT LPE200 Скачать руководство пользователя

Страница: 89 / 154

Electrical System – 5000 LWE 180/200 LPE 200

Troubleshooting

Order number

Date

Valid from serial number

T-code

225553-040

2005-05-11

723984-

660, 661, 662, 497

Service Guide

LWE180, LWE200, LPE200, LPE240

9- 51

9.9 Troubleshooting

9.9.1 Error codes and troubleshooting

The table below describes the error codes that can be displayed with
the status light or read on the hand unit.

STATUS LED

Text on hand
unit

Explanation

Possible cause

LED off

No voltage or error in
the regulator.

Defective fuse, poor contact, not con-
nected, error in the regulator.

LED on

Error in the regulator.

1,1

¤ ¤

CURRENT
SHUNT FAULT

Error in the built-in
current shunt.

Error in the rotor current sensor in the
motor monitor.

1,2

¤ ¤¤

HW FAILSAFE

CAN timeout in
power amplifier.

The motor monitor is reporting an
unexpected data loss from the tiller
arm head.

1,3

¤ ¤¤¤

M- SHORTED

Internal M- short
circuited to B-.

Problem with switch transistor in the
rotor circuit inside the motor monitor.

3,1

¤¤¤ ¤

CONT COIL/FLD
SHORT

Voltage too high for
contactor feed or
short-circuited field
winding.

Attempt to extract more current than
the output device can manage.
Problem regulating the field current.
Internal monitoring error.

3,3

¤¤¤ ¤¤¤

FIELD OPEN

Open field winding.

Shunt field open, defective cable,
defective motor monitor.

4,1

¤¤¤¤ ¤

LOW BATTERY
VOLTAGE

Low battery voltage.

1. Battery voltage < 17 volt.

2. Battery poles affected by corrosion.

3. Loose battery or regulator connec-
tions.

4,2

¤¤¤¤ ¤¤

OVERVOLTAGE

Voltage too high.

1. Battery voltage > 33 volt.

4,3

¤¤¤¤ ¤¤¤

THERMAL CUT-
BACK

Too high/too low
temperature reduc-
tion.

1. Temp. > 85

C or < -25

2. The truck is overloaded.

3. Incorrectly installed transistor

regulator.

4. Operation under extreme conditions.

MODEL

STATUS

SERIAL

VOLTAGE

CURRENT

Содержание LPE200



























































































































































Результаты поиска

Содержание LPE200

Отзывы:

Похожие инструкции для LPE200

Бренды по названию

Популярные бренды

BT LPE200, Руководство по обслуживанию

Результаты поиска

Содержание LPE200

Отзывы:

Похожие инструкции для LPE200

Бренды по названию

Популярные бренды