BT LPE200 Скачать руководство пользователя страница 151

Страница: 151 / 154

Hydraulic, pneumatic – 6000 LPE 240

Adjustments

Order number

Date

Valid from serial number

T-code

225553-040

2005-05-11

723984-

660, 661, 662, 497

Service Guide

LWE180, LWE200, LPE200, LPE240

12- 3

12.2 Adjustments

12.2.1 Adjustment of the pressure limit valve

The pressure limit valve is set to the correct value at the factory, but
may need to be adjusted if the valve or complete hydraulic unit is
replaced.

The truck should be able to lift a load of between 2250-2300 kg.

•

Unscrew the cover nut (1) with a spanner, 13 mm.

•

Place a load, 2200 kg, on the forks and check that the machine lifts
this.

•

If the machine can lift 2200 kg, place a further 100 kg on the forks.
Check whether machine can lift the load.

•

If the machine can lift 2300 kg, adjust the pressure limit valve by
screwing the adjuster screw (2) anticlockwise using a 4 mm allen
key until the machine cannot lift the load.

Pos.

Description

Notes

Cover nut

Adjuster screw,

pressure limit

Adjustment clockwise results
in increased pressure

Adjustment anticlockwise
results in reduced pressure

Содержание LPE200



























































































































































Результаты поиска

Содержание LPE200

Отзывы:

Похожие инструкции для LPE200

Бренды по названию

Популярные бренды

BT LPE200, Руководство по обслуживанию

Результаты поиска

Содержание LPE200

Отзывы:

Похожие инструкции для LPE200

Бренды по названию

Популярные бренды