BT LPE200 Скачать руководство пользователя | Manualshive

Страница: 134 / 154

background image

10- 42

Service Guide

LWE180, LWE200, LPE200, LPE240

© BT Europe AB

Electrical systems – 5000 LPE 240

Parameters

T-code

Valid from serial number

Date

Order number

660, 661, 662, 497

723984-

2005-05-11

225553-040

To start programming the expanded keypad:

•

Connect an appropriate CAN service key to X41

•

Enter code 341671 and press

on the keypad.

•

Select the programming command from Table 9:

•

Switch off the truck by pressing

on the keypad.

The expanded keypad programming is now complete

Parameter #39 must be set with the value 5, 6, 7 or 8 for the new PIN
codes to be valid.

Carry out a practical test by logging in using some of the new PIN
codes. It is important to establish that the correct driver profile has been
activated when a certain PIN code has been entered, especially if a
specific driver profile has been set for a specific application/goods han-
dling.

Table 10: shows the PIN codes available as standard in the program.
These can be activated for use or changed according to the driver’s
wishes.

One or more of these blocks can be activated.

A driver profile is activated, on normal login, by all PIN codes whose
block no. is activated.

The truck program does not approve login using the PIN code “0000”.

Service personnel should keep notes on activated blocks, changed PIN
codes and specially-set driver profiles.

NOTE!

Resetting the expanded keypad does NOT affect the driver profile set-
tings.

Table 9: Programming command - expanded keypad

Progamming

Function

Notes

Press “1” +

Reset to factory settings

Block 1 - 9 is deactivated.
Original PIN codes reset
as per Table 10:

Press “2” + B +

PIN codes in the block can be
used

B= Block no. 0 - 9

Press “3” + B +

PIN codes in the block cannot
be used

B= Block no. 0 - 9

Press “4” + B + F + NNNN +

Programming a new PIN code

B= Block no. 0 - 9
F= Driver profile no. 0 - 9
NNNN = PIN code

«
...
132
133
134
135
136
...
»

Содержание LPE200



























































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPE200

Бренд: Hyster Страницы: 19

Бренд: Mitsubishi Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды