BT LPE200 Скачать руководство пользователя страница 19

Страница: 19 / 154

Preventive maintenance – P2 LWE 180/200 LPE 200

Maintenance schedule

Order number

Date

Valid from serial number

T-code

225553-040

2005-05-11

723984-

660, 661, 662, 497

Service Guide

LWE180, LWE200, LPE200, LPE240

4- 1

4- Preventive maintenance – P2

LWE 180/200 LPE 200

4.1 Maintenance schedule

I: Inspect, rectify and change if necessary. T: Tighten. C: Clean. L: Lubricate.

M: Control measurement, rectify if necessary

Pos.
No.

Work to carry out

Interval in hours

500

1000

3000

Interval in days/weeks/months

12m

36m

0000

Chassis

0000.1

Check all links and locking pins

0000.2

Check wear on cover/battery locking

0000.3

Check of cracking and damage

0000.4

Check the cover locks

0000.5

Check finger guard

0000.6

Check signs and stickers

0000.7

Press grease into grease nipples

I/L

0380

Fork carriage

0380.1

Check for crack formation and damage

0380.2

Check clearance in bushes and links

0380.3

Press grease into grease nipples (Option)

I/L

0380.4

Check the lift limit switch

0560

Platform and mountings

0560.1

Check for any cracks or damage

0560.2

Check gas damper and cup springs

1700.

Drive motor

1700.1

Check clearance in connections

I/T

1700.2

Check the carbon brushes in the drive motor

1700.3

Clean the drive motor

1700.4

Re-tighten the attachment bolts

1700.5

Check for abnormal noise in bearing

Содержание LPE200



























































































































































Результаты поиска

Содержание LPE200

Отзывы:

Похожие инструкции для LPE200

Бренды по названию

Популярные бренды

BT LPE200, Руководство по обслуживанию

Результаты поиска

Содержание LPE200

Отзывы:

Похожие инструкции для LPE200

Бренды по названию

Популярные бренды