Brother GTX-4 Скачать руководство пользователя страница 134

Страница: 134 / 320

134

Basic printing procedures

(3)

Orient the pour spout of cock in the position as shown in the figure below.

X0081

(4)

Lean the entire shipping carton of pretreatment toward a container for dilution to pour the agent into the container,

and dilute it with pure water.



Use with the dilution rate of x3 (Pretreatment:Pure water=1:2) (Volume ratio).



Close the cap of the container for dilution, and shake it sufficiently to provide equal concentration.

X0082

(5)

To provide safekeeping for the pretreatment, close the cock, place the pretreatment with the cock part facing

upward, and store the entire carton in a safe place.

Pretreatment

Cock

Pretreatment

Pure water

Container for dilution

Содержание GTX-4

































































































































































































































































































































Результаты поиска

Содержание GTX-4

Отзывы:

Бренды по названию

Популярные бренды

Brother GTX-4, Инструкция по эксплуатации

Результаты поиска

Содержание GTX-4

Отзывы:

Бренды по названию

Популярные бренды