Brother BAS-300G-484 Скачать руководство пользователя страница 24

Страница: 24 / 88

3. INSTALLATION

BAS-300G-484, BAS-300G-484 SF

3-11. Connecting the power cord

1. Attach an appropriate plug to the

power cord (1). (The green and yellow
wire is the ground wire.)

Insert the plug into a
properly-grounded AC power supply.

* The inside of the control box uses

single-phase power.

NOTE:

Do not use an extension cord. If this is
not observed, it may cause problems
with correct operation.

3-12. Installing the cotton stand

(1) Cotton stand

NOTE:

Fit the washer (2), and then securely
tighten the nut (3) so that the cotton
stand does not move.

2974B

<Three-phase

specifications

<Single-phase

specifications

Green and yellow wire
(ground wire)

5239Q

Green and yellow wire
(ground wire)

Содержание BAS-300G-484

























































































Результаты поиска

Содержание BAS-300G-484

Отзывы:

Похожие инструкции для BAS-300G-484

Бренды по названию

Популярные бренды

Brother BAS-300G-484, Инструкция по эксплуатации

Результаты поиска

Содержание BAS-300G-484

Отзывы:

Похожие инструкции для BAS-300G-484

Бренды по названию

Популярные бренды