Brother BAS-300G-484 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 88

background image

10. STANDARD ADJUSTMENTS

BAS-300G-484, BAS-300G-484 SF

59

10-10. Adjusting the standby position of the movable knife

1.  Remove the top cover, the motor cover and the solenoid cover, and then tilt back the machine head.
2.  Turn the pulley (1) by hand in the direction of the arrow to move the needle bar to its lowest position.
3.  Loosen the bolt (2).
4.  Push the movable knife (3) in the direction of the arrow to take up the play, and then move thread trimmer rod H (4)

forward or back to adjust so that the V section (A) is aligned with the index mark (B) on the needle plate.

5. After tightening the bolt (2), check the above position once more.

6. Loosen the four bolts (5) and the nut (6) until the thread trimmer roller (7) is within the groove in the thread trimmer cam

(8). After this, tighten the set screw (9) until the thread trimmer roller (7) is touching the inside of the groove in the thread
trimmer cam (8) and then turn it back in the counterclockwise direction by approximately 1/4 of a turn. Then tighten the nut
(6).

4695M

4696M

«
...
66
67
68
69
70
...
»

Содержание BAS-300G-484

























































































Отзывы:

Нет отзывов

Похожие инструкции для BAS-300G-484

Бренд: Clarke Страницы: 61

Бренд: Weslo Страницы: 12

Бренд: Kärcher Страницы: 15

Бренд: Toyota Страницы: 48

Бренд: R+M Suttner Страницы: 4

Cover Stitch Wide

Бренд: Singer Страницы: 13

Бренд: Pfaff Страницы: 36

Бренд: Truvox Страницы: 16

Бренд: Singer Страницы: 50

Snack Safety Point SVE SSP

Бренд: SandenVendo Страницы: 44

Бренд: JUKI Страницы: 36

Бренд: Konica Minolta Страницы: 92

Бренд: JUKI Страницы: 2

Бренд: JUKI Страницы: 4

Бренд: Janome Страницы: 91

THERMALBINDER400T

Бренд: GBC Страницы: 28

WireBind E-Karo 40Pro

Бренд: GBC Страницы: 38

Бренд: GBC Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды