Brother BAS-300G-484 Скачать руководство пользователя страница 80

Страница: 80 / 88

11. TABLE OF ERROR CODES

BAS-300G-484, BAS-300G-484 SF

Data editing-related errors

Code

Cause and remedy

E500

The enlargement ratio setting caused the sewing data to extend outside the sewing area.
Set the enlargement ratio again.

E501

Sewing data that exceeds the sewing machine's sewing area was loaded.
Check the size of the sewing data.

E502

The enlargement ratio caused the data pitch to exceed the maximum pitch of 12.7 mm.
Set the enlargement ratio again.

E510

Invalid code in sewing data.
Reload the data from the CF card or floppy disk.

E511

No end code has been input into sewing data.
Input an end code, or change the program number.

E512

Number of stitches exceeds allowed maximum.

E520

Extended option output number already exists. Change the extended option output number.
If not using the extended option output, initialize the data to clear the extended option output data.

E530

Changing program number is prohibited.

Device-related errors

Code

Cause and remedy

E670

Turn off the power, and then contact the place of purchase.

E671

Turn off the power, and then contact the place of purchase.

Содержание BAS-300G-484

























































































Результаты поиска

Содержание BAS-300G-484

Отзывы:

Похожие инструкции для BAS-300G-484

Бренды по названию

Популярные бренды

Brother BAS-300G-484, Инструкция по эксплуатации

Результаты поиска

Содержание BAS-300G-484

Отзывы:

Похожие инструкции для BAS-300G-484

Бренды по названию

Популярные бренды