Brother BAS-300G-484 Скачать руководство пользователя страница 21

Страница: 21 / 88

3. INSTALLATION

BAS-300G-484, BAS-300G-484 SF

3-9. Connecting the cords

1. Gently tilt back the machine head.
2. Pass the cord bundle through the hole

in the work table.

3. Loosen the two screws (1), and then

open the cord presser plate (2) in the
direction of the arrow and pass the
cord bundle through the opening
together with the following cords.

•

Two-pedal foot switch (3)

•

Operation panel (Do not pass the

ground wires through the hole.)

•

Solenoid valve assembly

4. Securely connect the connectors as

indicated in the table below.

<Main P.C. board>

NOTE:

•

Check that the connector is facing the correct

way, and then insert it firmly until it locks into
place.

•

Secure the cables with cable ties and cord

clamps, while being careful not to pull on the
connector.

*1:

Be sure to make the ground connection.

(Refer to "3-10. Connecting the ground wire".)

*2:

Only applicable to -484 SF specifications.

Connector

Connection location on

main P.C. board

Cord clamp

X pulse motor encoder 5-pin white

P20 (X-ENC)

(3)

Y pulse motor encoder 5-pin blue

P4 (Y-ENC)

(3)

Work clamp pulse motor encoder 5-pin black

P5 (P-ENC)

(3)

Foot switch 10-pin

P6 (FOOT)

(3)

Operation panel 8-pin

P1 (PANEL)

(3)

Machine head switch 3-pin

P9 (HEAD-SW)

(4)

Home position sensor assembly 12-pin

P8 (SENSOR1)

(4)

STOP switch 6-pin

P13 (HEAD)

(4)

Valve harness 12-pin

P12 (AIR1)

(4)

Valve harness 5-pin

P26 (AIR3)

(4)

Programmer relay harness 8-pin

P7 (PRG)

(3)

Solenoid selection harness 4-pin

P3 (CUTTER)

－

Thread trimming cylinder sensor harness 16-pin

P23 (EX-IN1)

(4)

Lock the cord
clamp securely.

(Continued on next page)

4649M

4650M

Содержание BAS-300G-484

























































































Результаты поиска

Содержание BAS-300G-484

Отзывы:

Похожие инструкции для BAS-300G-484

Бренды по названию

Популярные бренды

Brother BAS-300G-484, Инструкция по эксплуатации

Результаты поиска

Содержание BAS-300G-484

Отзывы:

Похожие инструкции для BAS-300G-484

Бренды по названию

Популярные бренды