Bronpi Dama Hydro, Инструкция по установке, эксплуатации и обслуживанию

Страница: 37 / 120

36
Programme 3: Monday (OFF), Tuesday (ON), Wednesday (ON),
Thursday (ON), Friday (ON), Saturday (ON), and Sunday (OFF.)
Programme 4: Monday (ON), Tuesday (ON), Wednesday (OFF),
Thursday (OFF), Friday (OFF), Saturday (OFF), and Sunday (ON.)
Thanks to this type of setting we can combine 4 different times
throughout the days of the week, but always keeping in mind not to
superimpose or intermesh the times.
Sub-menu 02-04- Weekend Programme
In the same way as in the daily programme, this setting up has two independent times to start and two to stop, with the precision that it only
applies to Saturday and Sunday. To access this setting up we need
to start from the following screen ( see drawing D44 ):
We need to confirm the access to this programme by pressing
button no.3 “SET” and it should show the following screen ( see
drawing D45
):
We modify the value “OFF” and select “ON”: Finally, we introduce the
times to start and stop in order to complete the desired setting up.
As in the daily programme, if we need to set up only one time to start and stop, the options START 2 and STOP 2 should indicate “OFF.”
It is also possible to schedule one automatic start hour and manual stop hour (or vice versa).
Example: START 1: 00:1 hours and STOP 08: “off”
or
START 1: “off” and STOP 1: 22:00 hours.
9.4.4 MENU 3. SELECT LANGUAGE
It allows selecting the languages among those available. To access
to this menu you have to confirm with button nº 3 “SET” and then,
choose the selected language among those available: Spanish, English, French, Italian, German and Portuguese with buttons nº 1 and 2
( see drawing D46 ).
9.4.5 MENU 4. STAND-BY MODE
In case of thermo-stoves, once the ambient or water temperature
reaches the temperature set plus a differential (2º C) by the user
and it is activated “stand-by mode” the thermo-stove will be
automatically turned off. When the ambient temperature falls to
the set temperature minus a differential (2ºC) the thermo-stove
automatically restarts an ignition cycle. It means that if you choose
an ambient temperature of 22ºC the thermo-stove will turn-off when the room temperature is 24º C and it will restart automatically when the
ambient temperature falls to 20ºC, independently of the water temperature.
In case of the “Stand-by Mode” is deactivated (by default) the
thermo-stove will work by modulating the power when it reaches
one of both temperatures, that allows the temperature set could be
higher.
9.4.6 MENU 5 - SOUND MODE
By activating this mode, the thermo-stove will emit a sound when the
system detects a fault and goes into the alarm state. To access to
this menu you have to confirm with button nº 3 “SET” and then, choose “on” with buttons nº 1 and 2 ( see drawing D48 ).
9.4.7 MENU 6. INITIAL LOAD
In case of the thermo-stove has run out of fuel during the operation,
in order to avoid an anomaly in the next ignition, it is possible to
carry out a fuel pre-load for a maximum time of 90 seconds to
load the auger feeder. This can be used when the thermo-stove is
switched off and cold. To start the pre-load press button nº 2 and to
stop it press button nº 4 ( see drawing D49 ).
It is very important that the burner is totally empty when you start the thermo-stove. So, when the initial pre-load is finished, you
must check the burner is clear of fuel in order to achieve correct ignition of the thermo-stove.
9.4.8 MENU 7- STOVE STATE
It shows the current state of the thermo-stove and
provides information about the devices connected.
Therefore, the user can get some technical information.
The next screens are seen automatically ( see drawings
D50, D51, D52 and D53 ).
On
D48
Menu 05
SOUND
MODE
77”
D49
LOAD
INITIAL
22ºC 28ºC
D50
STATE
TIME 1 REMAINING TIME INTERMEDIATE CLEANING
STATE ALARM DELAY OPERATIONAL STATE
SPA
D46
Menu 04
D44
PROGRAMME
WEEKEND
M-2-4
Off
D45
PROGRAMME
WEEKEND
M-2-4-01
On
D47
Menu 04
STAND-BY
MODE
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS HYDRO SERIES
EN