8
96
Front
1. See Figure 139. Move the throttle control lever (
A
) to
the FAST position.
2. Hold the cable mounting nut (
B
) and loosen Phillips
screw (
C
). Rotate nut to accept cable wire.
3. Insert the cable wire through the hole in cable
mounting nut, so that it does not extend more than
1/2 inches
(12.7 mm) past the exit hole.
4. Hold the cable mounting nut and tighten Phillips
screw.
5. Loosen hex screw (
D
) and capture cable sheath in
casing clamp (
E
). Tighten screw.
6. Verify that return spring (
F
) is installed.
7. Remove the control link (
G
), if present.
8. Exercise the throttle control lever to verify that lever
and cable move freely without sticking or binding.
9. Install air cleaner. See
AIR CLEANER
in this section.
Solid Wire Cable
NOTE:
The solid wire cable is installed in one of four
directions.
Cylinder Head
1. See Figure 140. Move the throttle control lever (
A
) to
the FAST position.
2. Verify that nut (
B
) on throttle control lever is loose
(1/2 turn from tightened position).
3. Install Z-fitting of cable into either hole (
C
) in
bellcrank.
4. Loosen hex screw (
D
) and capture cable sheath in
casing clamp (
E
). Tighten screw.
NOTE:
Use the internal T25 TORX recess for best
results.
5. Exercise the throttle control lever to verify that lever
and cable move freely without sticking or binding.
6. Install air cleaner. See
AIR CLEANER
in this section.
Front
1. See Figure 141. Move the throttle control lever (
A
) to
the FAST position.
2. Verify that nut (
B
) on throttle control lever is loose
(1/2 turn from tightened position).
3. Install Z-fitting of cable into either hole (
C
) in
bellcrank.
4. Loosen hex screw (
D
) and capture cable sheath in
casing clamp (
E
). Tighten screw.
140
141
5. Exercise the throttle control lever to verify that lever
and cable move freely without sticking or binding.
6. Install air cleaner. See
AIR CLEANER
in this section.
Left
1. See Figure 142. Remove black knob (
A
) from throttle
control lever, if installed. For best results, tap knob
from behind using a flat punch and soft mallet.
2. Move the throttle control lever (
B
) to the FAST
position.
3. Verify that nut (
C
) is loose (1/2 turn from tightened
position).
4. Install air cleaner. See
AIR CLEANER
in this section.
Not for
Reproduction
Содержание Vanguard 10V300
