8
95
A. Insert solder lug of white wire under engine or
frame bolt for suitable ground (
B
).
B. Tightly coil red wire over an insulated section of
the spark plug wire using three to four turns (
C
).
NOTE:
Keep wires away from hot or moving
engine parts.
3. Set throttle control lever (
D
) to FAST (
E
) and start
engine.
4. Using a small screwdriver, push against OFF STOP
(
F
) until throttle control lever is at idle or main
governor spring is slack.
5. Move governor lever (
G
) until throttle lever contacts
end of dead idle screw (
H
).
6. Adjust dead idle screw to set dead idle speed to 1000
+/- 100 RPM.
7. Set throttle control lever to IDLE (
I
).
8. Obtain Tang Adjusting Tool (Part No. 19480).
9. Bend idle speed adjustment tang (
J
) to set idle speed
to 1450 +/- 100 RPM.
NOTE:
Do not twist or rotate tang. Only bend in same
plane as spring acts.
10. Move throttle control lever to FAST.
11. Bend high speed adjustment tang (
K
) on control
bracket to set top no-load speed value obtained in
step 1.
12. Stop engine and remove Digital Tachometer and
Hour Meter.
Remote Control
Remove the air cleaner. See
SECTION 4 - REMOVE
EXTERNAL ASSEMBLIES, AIR CLEANER.
Braided Wire Cable
NOTE:
The braided wire cable is installed in one of two
directions.
Cylinder Head
1. See Figure 138. Move the throttle control lever (
A
) to
the FAST position.
2. Hold the cable mounting nut (
B
) and loosen Phillips
screw (
C
). Rotate nut to accept cable wire.
3. Insert the cable wire through the hole in cable
mounting nut, so that it does not extend more than
1/2 inches
(12.7 mm) past the exit hole.
4. Hold the cable mounting nut and tighten Phillips
screw.
5. Loosen hex screw (
D
) and capture cable sheath in
casing clamp (
E
). Tighten screw.
NOTE:
Use the internal T25 TORX recess for best
results.
6. Verify that return spring (
F
) is installed.
7. Remove the control link (
G
), if present.
8. Exercise the throttle control lever to verify that lever
and cable move freely without sticking or binding.
9. Install air cleaner. See
AIR CLEANER
in this section.
138
139
Not for
Reproduction
Содержание Vanguard 10V300
