Briggs & Stratton 5 HP Скачать руководство пользователя

Страница: 56 / 76

3. Compress spring until valve stem extends through

large end of retainer slot. Continue to press until
small end of slot can slide into groove on valve stem.
Be sure retainer is fully engaged to valve stem groove.

Install Cylinder Head

NOTE

: Do not use sealer on gaskets.

1. Coat threads of cylinder head screws with Valve

Guide Lubricant

(#93963)

2. Place new cylinder head gasket on dowel pins and

then install cylinder head and cylinder head screws.

3. Torque screws in sequence as numbered on cylinder

head, or as shown

(Figure 98)

. Tighten the cylinder

head in three steps:

NOTE

: Do not tighten any screw to the final

torque before all screws have been tightened to the
second step. Uneven tightening may cause a warped
cylinder head.

First step:

70 in. lbs. (8 Nm)

Second step:

140 in. lbs. (16 Nm)

Final step:

210 in. lbs. (24 Nm)

Install Rocker Arms

1. Install push rods

(Figure 99)

through push rod

guide making sure push rods are in valve tappets

2. Remove all lubricant from end of valve stems.

3. Place valve caps

(Figure 100)

on end of valve

stems. Do not use lubricant on the valve caps.

4. Place rocker arms on studs and install rocker arm

adjusting nuts

and set screws while holding rocker

arm against valve cap and pushrod until nut is finger
tight.

5. Rotate crankshaft at least two revolutions to be sure

push rods operate rocker arms.

Section 5 • Assembly

5 HP Outboard • Troubleshooting & Repair Manual

Figure 98 — Torque Cylinder Head Bolts

Figure 99 — Install Rocker Arms

‚

Figure 100 — Valve Caps & Adjusting Nuts

Содержание 5 HP













































































Результаты поиска

Содержание 5 HP

Отзывы:

Похожие инструкции для 5 HP

Бренды по названию

Популярные бренды

Briggs & Stratton 5 HP, Руководство по устранению неполадок и ремонту

Результаты поиска

Содержание 5 HP

Отзывы:

Похожие инструкции для 5 HP

Бренды по названию

Популярные бренды