Briggs & Stratton 5 HP Скачать руководство пользователя

Страница: 17 / 76

Armature Test

1. Disconnect the ground lead

(Figure 12)

to the

armature,

2. Connect spark plug wire

to long terminal of Spark

Tester

(#19368)

and ground tester to engine.

3. Pull the starter rope and observe the spark gap in the

tester. If the spark jumps the tester gap, the armature
is good.

4. If there is no spark, check the ground lead for

pinching, worn insulation or damage. Test the lead for
continuity. If the ground lead is undamaged and has
continuity, replace the armature.

Tests for No Spark

NOTE:

Perform these tests if the armature is good

and there is still no spark.

1. Remove the cowl from the power head.
2. Disconnect the armature ground lead.

3. Remove safety/engine stop switch clip

(Figure 13)

4. Disconnect the wiring harness connector

(Figure 14)

from the engine speed limiter.

5. Insert the test probe to the wire harness side of the

armature ground wire connector

6. Test the switch for continuity at the engine ground

There should be continuity.

Section 2 • Troubleshooting

5 HP Outboard • Troubleshooting & Repair Manual

Figure 12 — Armature Test

Figure 13 — Safety Stop Switch Clip

Figure 14 — Disconnect Speed Limiter

WARNING

Do not remove spark plug when
checking ignition. A fire or
explosion may occur. Always use
an approved spark tester.

Содержание 5 HP













































































Результаты поиска

Содержание 5 HP

Отзывы:

Похожие инструкции для 5 HP

Бренды по названию

Популярные бренды

Briggs & Stratton 5 HP, Руководство по устранению неполадок и ремонту

Результаты поиска

Содержание 5 HP

Отзывы:

Похожие инструкции для 5 HP

Бренды по названию

Популярные бренды