Braun 0871 3050 Скачать руководство пользователя страница 34

Страница: 34 / 136

Unit Diagnosis / Calibration

2 - 4

Infusomat® Space 6.0

Error Codes of the Control Microprocessor

* Note: If alarm 2111 occurs during infusion, the device history logs may not be re-
trievable.

Error Code

Definition

Possible Cause

Fault Clearance

2100

Timebase too fast

Quartz of the processor PCB

Exchange processor PCB

2101

Timebase too slow

Quartz of the processor PCB

Exchange processor PCB

2102

Timebase failure

Quartz of the processor PCB

Exchange processor PCB

2103

Keyboard High

Keyboard defective

Exchange operating unit

2104

ON/OFF key pressed too long

Keyboard defective

Exchange operating unit

2105

No keydecode

Keyboard defective

Exchange operating unit

2106

ROM Romtest defective

Software

Update unit software

2107

ROM program defective

2108

FuP has not changed active reset value

10 2109

MPU_Test failed

11 2110

RAM_Test failed

12 2111*

KUP active reset

Pump was not switched off cor-
rectly

Restart device

13 2112 2114

Internal Error

14 2115

Drive too fast

Motor drive
Detection of direction of rotation

Exchange processor PCB

15 2116

Drive too slow

16 2117 ... 2118 Internal Error

17 2119

LCD backlight on defective

LC display defective

Exchange operating unit

18 2120

LCD backlight off defective

19 2121

Red LED on defective

20 2122

Red LED off defective

21 2123

Key pressed too long (without ON/OFF
key)

Keyboard defective

Exchange operating unit

22 2124 ... 2127 Internal Error

23 2128

Drive motion incorrectly forward

Motor drive
Detection of direction of rotation

Replace processor PCB

24 2129

Drive motion incorrectly backward

25 2130 ... 2159 Internal Error

26 2160 ... 2162 PCA Error

Error in relation to PCA therapy
together with special settings

Restart the device, change settings
slightly if necessary. If the error per-
sists: Please load the history file via
HiBaSeD and inform B. Braun

27 2170 ... 2173 DLOCK Error

Error in relation to Datalock to-
gether with special settings

Restart the device, change settings
slightly if necessary. If the error per-
sists: Please load the history file via
HiBaSeD and inform B. Braun

Table 2 - 3 Error Codes of the Control Microprocessor (Part 1 of 3)

Содержание 0871 3050









































































































































Результаты поиска

Содержание 0871 3050

Отзывы:

Похожие инструкции для 0871 3050

Бренды по названию

Популярные бренды

Braun 0871 3050, Руководство по обслуживанию

Результаты поиска

Содержание 0871 3050

Отзывы:

Похожие инструкции для 0871 3050

Бренды по названию

Популярные бренды