Bradley Lenox Скачать руководство пользователя страница 14

Страница: 14 / 15

Lenox® Lockers (includes Cubby & “Z” Lockers)

Installation

10/24/07

Bradley Corporation • LK-INSTR-001 Rev. K; EN 07-1303

Figure 10a

ANGLE

BRACKET

(HW0019)

#10-1/2" LG.

SCREW

(FAST-T349)

Installation Instructions continued . . .

Step 10: Back-To-Back Locker Slope Top Installation

NOTE: Mounting strips will be 54" maximum length. Color of strips may vary.

1. Drill 3/16" dia. clearance holes through the top of the installed lockers, making sure that the

holes are located 1-1/4" from the front edge of the locker (see Figure 7a on page 9).

2. Position the slope top mounting strips on top of the lockers as shown in Figure 10a.

3. Temporarily clamp the slope top mounting strips together, making sure they are flush and

aligned.

4. Using the 2" mounting brackets and hardware supplied, anchor the mounting strips to the top of

the locker as shown in Figure 10a.

5. Position the slope top on top of the lockers as shown in Figure 10b on page 15, fitting the slope

top groove over the edge of the locker.

6. Hold the slope top down tight against the top of the locker and secure with the #8 x 1-1/4"

screws provided (see Figure 10b). Do not overtighten the screws.

7. Install the remaining slope top sections per the instructions outlined above.

NOTE: If desired, caulk the gap in the back edge of the slope top where it meets the wall strip.

Содержание Lenox
















Результаты поиска

Содержание Lenox

Отзывы:

Похожие инструкции для Lenox

Бренды по названию

Популярные бренды

Bradley Lenox, Руководство по установке

Результаты поиска

Содержание Lenox

Отзывы:

Похожие инструкции для Lenox

Бренды по названию

Популярные бренды