Solution 64 | Installer Guide | Input Programming
Bosch Security Systems | 11/05 | BLCC110I
7-11
Inputs > Tamper Inputs >
Tamper Options
MENU 3-6-0
1
Display Panel Tamper
Y
2
Report Panel Tamper
Y
3
Audible Panel Tamper
Y
4
Display Expander Tamper
N
5
Report Expander Tamper
N
6
Audible Expander Tamper
N
7
Reserved
N
8
Reserved
N
This menu programs how the various system tamper inputs behave
when faulted. These dedicated tamper inputs are active 24 hours a
day when enabled.
Press [MENU] + [3] + [6] + [0]. The keypad will display the
current tamper options.
Display Box Tamper
Report Box Tamper
Audible Box Tamper
Press
OK ON OFF MENU
Use the up and down arrow keys to highlight the option then
press the [ON] key to enable or the [OFF] key to disable.
Repeat Step 2 until all options are programmed as required,
then press [OK] to save and exit or press [MENU] to exit
without saving.
Display Enclosure Tamper
Setting this option allows the keypad to display a trouble condition
when the tamper circuit that monitors the systems enclosure is
faulted. The trouble condition will clear when the tamper circuit has
restored.
Report Enclosure Tamper
Setting this option allows the panel to send a Enclosure Tamper report
when the enclosure tamper circuit is faulted. A Enclosure Tamper
Restore report will be sent when the tamper circuit has restored.
Audible Enclosure Tamper
Setting this option will cause the panel to sound the sirens when the
enclosure tamper circuit is faulted.
Display Expander Tamper
Setting this option causes the system to display tamper events which
have occured on peripheral modules.
Report Expander Tamper
Setting this option enables peripheral tamper reporting.
Audible Expander Tamper
Setting this option causes the system to trigger an audible alarm
when a peripheral tamper is triggered.
1)
2)
3)
Input Testing
Inputs > Input Testing >
Walk Test All Zones
-
-
MENU 3-9-0
This menu allows you to test all zones within an area at the
same time. To perform a successfull walk test, each zone in the
area must be sealled and unsealled. Users must have access to
the area they want to test.
Once the mode is activated all zones in the area will be listed
one after the other on the keypad display. As each zone is
successfully tested it will be removed from the list leaving only
those zone still to be tested in the list.
Press [MENU] + [3] + [9] + [0] and select the area to walk test
from the list then press [OK].
The keypad will begin scrolling all of the zones that are to be
tested as per the below display.
To test Zn001 open/close
Zone 1
Press OK or MENU
To test Zn002 open/close
Zone 2
Press OK or MENU
Open and close each zone in the list. Zones that have been
successfully tested are removed from the keypad scroll list.
When all zones have been tested, the keypad will display:
Selected zones have been
tested OK
Press OK or MENU
Press [OK] or [MENU] to exit.
Inputs > Input Testing >
Walk Test A Zone
-
-
MENU 3-9-1
This menu allows you to select a single zone to be walk tested.
To perform a successfull walk test, the sellected zone must be
sealled and unsealled. Users must have access to the zone they
want to test.
Press [MENU] + [3] + [9] + [1] and use the up and down arrows
to highlight the zone you want to walk test in the list and
press[OK]. Alternatively, you can enter the zone number
directly and press [OK].
The keypad will display the zone to be tested.
To test open/close
Zone 1 Name
Press OK or MENU
1)
2)
3)
4)
1)
2)
