Bosch Rexroth RE 90300-B Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 64

background image

14

/64

Axial piston units

|

Safety instructions

Bosch Rexroth AG, RE 90300-B/2021-01-19

2.6 Product-specific safety instructions

The following safety instructions apply to chapters 6 t o 14.

WARNING

Danger from excessive pressure!

Risk of death or injury, or property damage!
Improperly changing the factory pressure settings can result in a pressure increase
beyond the maximum permissible pressure.
Operating the unit above the maximum permissible pressure can cause
components to burst and hydraulic fluid to escape under high pressure.

▶ Changes to the factory settings may only be made by Bosch Rexroth specialists.

▶ In addition, a pressure relief valve is required in the hydraulic system as back-up.

If the axial piston unit is equipped with a pressure cut-off and/or pressure
controller, this is not an adequate safeguard against pressure overload.

Danger due to suspended loads!

Risk of death or injury, or property damage!
Improper transportation may cause the axial piston unit to fall down and lead to
injury, e.g. crushing or fracture, or damage to the product.

▶ Make sure that the load bearing capacity of the lifting device is sufficient to

safely bear the weight of the axial piston unit.

▶ Never step or grip under suspended loads.

▶ Ensure a stable transport position.

▶ Use your personal protective equipment (e.g. safety goggles, safety gloves,

suitable working clothes, safety shoes).

▶ Use suitable lifting devices for transport.

▶ Observe the prescribed position of the lifting strap.

▶ Observe the national laws and regulations on occupational health and safety,

and transportation.

System/machine under pressure!

Risk of death or serious injury when working on unsecured machines/systems!
Property damage!

▶ Switch off the relevant machine/system part and secure it against reactivation

according to the parameters by the machine/system manufacturer.

▶ Ensure that all relevant components of the hydraulic system are depressurized.

For this purpose, observe the parameters indicated by the machine/system
manufacturer.

▶ Please note that the hydraulic system might still be pressurized even after

separation from the actual pressure supply.

▶ Do not disconnect any line connections, ports or components as long as the

hydraulic system is under pressure.

«
...
12
13
14
15
16
...
»

Содержание Rexroth RE 90300-B

































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth RE 90300-B

Бренд: Daavlin Страницы: 13

Бренд: Daavlin Страницы: 27

Бренд: Parker Research Corp Страницы: 3

Бренд: S.I.T.A. Страницы: 32

Бренд: Canta Страницы: 2

Бренд: Danelec Страницы: 67

Pro Vantage 12+ Series

Бренд: Ecco Страницы: 6

Бренд: Federal Signal Corporation Страницы: 12

Бренд: Garelick Страницы: 2

Бренд: Garelick Страницы: 2

Бренд: Taurus Страницы: 24

Бренд: Labnet Страницы: 12

Accublock D1301

Бренд: Labnet Страницы: 13

ST60+ SPEED INSTRUMENT

Бренд: Raymarine Страницы: 60

Бренд: Raymarine Страницы: 15

Бренд: RaycoWylie Страницы: 9

Бренд: Raven Страницы: 58

Бренд: Raven Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды