Bosch Rexroth RE 90300-B Скачать руководство пользователя страница 57

Страница: 57 / 64

RE 90300-B/2021-01-19, Bosch Rexroth AG

Troubleshooting |

Axial piston units

/64

14.3 Axial piston motor malfunction table

Table 10: Axial piston motor malfunction table

Malfunction

Possible cause

Remedy

Unusual noises

Insufficient air bleeding of the hydraulic system Fill the axial piston unit, suction line for the

hydraulic pump and the reservoir
Completely air bleed the axial piston unit and
hydraulic system
Check correct installation position

Output speed too high

Machine/system manufacturer: Reduce output
speed

Improper mounting of the axial piston unit

Check the mounting of the axial piston
unit according to the specifications of the
machine/system manufacturer – observe
tightening torques

Improper mounting of assembled parts,
hydraulic lines or improper installation of the
coupling

Fasten assembled parts according to the
parameters provided by the coupling fitting
manufacturer

Mechanical damage to the axial piston unit
(e.g. bearing damage)

Replace axial piston unit

Contact Bosch Rexroth Service

Increased, unusual vibration

Bearings worn

Contact Bosch Rexroth Service

No or insufficient pressure

Insufficient air bleeding of the hydraulic system Fill the axial piston unit, suction line for the

hydraulic pump and the reservoir
Check correct installation position

Faulty mechanical output drive (e.g., defective
coupling)

Contact machine/system manufacturer

Drive power too low

Contact machine/system manufacturer

Malfunction of the control device or controller
of the axial piston unit

Contact Bosch Rexroth Service

Control of the control device defective

Check control (contact machine/system
manufacturer or Bosch Rexroth Service)

Wear or mechanical damage to the axial piston
unit

Replace axial piston unit

Contact Bosch Rexroth Service

Drive unit defective (e.g. hydraulic pump)

Contact machine/system manufacturer

Pressure/flow fluctuations/
instabilities

Insufficient air bleeding of the hydraulic system Fill the axial piston unit, suction line for the

hydraulic pump and the reservoir
Completely air bleed the axial piston unit and
hydraulic system
Check correct installation position

Unstable control signal

Contact machine/system manufacturer or
Bosch Rexroth Service

Malfunction in the control devices or the
controller

Contact Bosch Rexroth Service

Содержание Rexroth RE 90300-B

































































Результаты поиска

Содержание Rexroth RE 90300-B

Отзывы:

Похожие инструкции для Rexroth RE 90300-B

Бренды по названию

Популярные бренды

Bosch Rexroth RE 90300-B, Инструкция по эксплуатации

Результаты поиска

Содержание Rexroth RE 90300-B

Отзывы:

Похожие инструкции для Rexroth RE 90300-B

Бренды по названию

Популярные бренды