Bosch Rexroth RE 90300-B Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 64

background image

RE 90300-B/2021-01-19, Bosch Rexroth AG

Maintenance and repair |

Axial piston units

49

/64

10.4 Repair

Bosch Rexroth offers a comprehensive range of services for the repair of Rexroth
axial piston units.
Repairs on the axial piston unit and its assembled parts should only be performed by
service centers certified by Bosch Rexroth.

▶ Only use original spare parts from Rexroth to repair the Rexroth axial piston units,

otherwise the functional reliability of the axial piston unit cannot be guaranteed,
and the warranty will be voided.

For questions regarding repairs, contact your proper Bosch Rexroth service partner
or the service department of the manufacturer's plant of the axial piston unit;
see chapter 10.5 "Spare parts" on page 49.

10.5 Spare parts

CAUTION

Use of unsuitable spare parts!

Spare parts that do not meet the technical requirements specified by
Bosch Rexroth can cause injury and property damage!

▶ Only use original spare parts from Rexroth to repair the Rexroth axial piston

units, otherwise the functional reliability of the axial piston unit cannot be
guaranteed, and the warranty will be voided.

The spare parts lists for axial piston units are order-specific. When ordering spare
parts, specify the material and serial number of the axial piston unit as well as the
material numbers of the spare parts.
Address all questions regarding spare parts to your proper Bosch Rexroth Service
partner or the service department of the manufacturer's plant of the axial piston unit.
Details for the manufacturer's plant can be found on the name plate of the axial
piston unit.

Bosch Rexroth AG
Glockeraustraße 4
89275 Elchingen, Germany
H49 9352 405060

Bosch Rexroth AG
An den Kelterwiesen 14
72160 Horb a.N., Germany
H49 9352 405060

Spare parts can be found online at

www.boschrexroth.com/eshop

For general inquiries, please contact your local contact person. You can find their
contact information at

www.boschrexroth.com/addresses

«
...
47
48
49
50
51
...
»

Содержание Rexroth RE 90300-B

































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth RE 90300-B

Бренд: Taurus Страницы: 28

Бренд: Kärcher Страницы: 54

Бренд: ABB Страницы: 85

Бренд: Taylor Страницы: 70

Бренд: Raith Страницы: 26

Бренд: Kane Страницы: 16

Бренд: Keiser Страницы: 2

Бренд: ECA Страницы: 3

Бренд: Nautilus Страницы: 12

Бренд: ParaBody Страницы: 6

Бренд: Sailmon Страницы: 10

Бренд: B&W Tek Страницы: 12

Бренд: b&o Страницы: 46

Бренд: Cadex Страницы: 300

BODY ARMOR PRO TERM

Бренд: Darco Страницы: 6

Бренд: ICELED Страницы: 4

Бренд: Facom Страницы: 4

Бренд: FaceLake Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды