manualshive.com logo in svg

Bosch K2200 Series, Руководство пользователя

Поделиться
Скачать
Bosch K2200 Series Скачать руководство пользователя страница 49

K2200 Series | 

User Guide | 6.0

Installer Commands

EN 

| 49

Bosch Security Systems | 7/03 | 17376 v1.1 / 47491C

6.2.5

Relay Programming

 - The RE Command: There are two types of relay
that can be activated. They are:

•

 

The 4 relays located on each door controller.

•

 

The 4 relays located on each alarm module.

The relays on the alarm modules can be activated by
alarm module Inputs as described above, in the MS
command. This section describes how to use both
these types of relay to respond to other events

There are two types of event to which these relays
can respond; system events and time profiles. It is
unlikely that you will activate a relay on both a
system event and time profile, however, it is possible
- the relay will stay set until all conditions are clear.

System Events

The following table shows the types of event and
their code number that can be assigned to a relay.

Table 24: Event Types

System
Event

Relay

Code

Notes:

No Response

0

Door Alarm on
any door

1

An alarm event (i.e.
unauthorized access, cable
tamper, etc.) at any of the four
doors on the door controller
will activate a relay given this
code. The relay will not be
deactivated until all such
alarms are cleared. This is the
same as the default action
given to relay 1 if not
programmed otherwise.

Door Left
Open on any
door

2

This code will activate a relay
if any of the four doors on the
door controller are left open
and it will be deactivated
when all the doors are closed.
This is the same as the default
action given to relay 3 if not
programmed otherwise

Case Tamper

3

Door 1 Open

4

Door 2 Open

5

Door 3 Open

6

Door 4 Open

7

These codes will activate a
relay if the particular door is
opened for any reason.  It will
deactivate when the door is
closed.

Door 1 Left
Open

8

Door 2 Left
Open

9

Door 3 Left
Open

10

Door 4 Left
open

11

These codes will activate a
relay if the particular door is
left open and it will deactivate
when the door is closed

Door 1 Alarm

12

Door 2 Alarm

13

Door 3 Alarm

14

Door 4 Alarm

15

These codes will activate a
relay if the particular door has
an alarm event, i.e.
unauthorized access or cable
tamper, and it will deactivate
when the alarm is cleared

Time Profiles

A relay can be made to operate with a time profile.
When the time profile is active, the relay will be set.
Examples are the use of external lighting, switching
heating or ventilation systems, etc.

Using the RE Command

There are 16 relay records, one for each alarm
module.

Содержание K2200 Series































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды