Bosch K2200 Series Скачать руководство пользователя страница 46

K2200 Series | 

User Guide | 6.0

Installer Commands

EN 

| 46

Bosch Security Systems | 7/03 | 17376 v1.1 / 47491C

6.2

Alarm Event Manager and Relay
Outputs

6.2.1

Overview

The Alarm Event Manager is an optional alarm
module that can be attached to any reader channel. It
can be attached at any point in the cable between the
door controller and reader. The alarm module has 8
inputs and 8 relay outputs 

but relays 5 to 8 can only

administrated by Readykey for Windows

.

8 Monitored Inputs

Each alarm module can monitor up to 8 inputs and
generate an alarm if any enabled input is activated.

Each input may be:

 

Normally Open or Normally Closed (set on the
module itself)

 

Enabled/Disabled Manually

 

Enabled/Disabled using a time profile

 

Programmed to activate a relay.

8 Relay Outputs

The 8 relay outputs on the module may be activated
by:

 

An monitored input being activated.

 

A system event.

 

A time profile.

6.2.2

Identiying Modules, Inputs and Relays

Each reader channel on a door controller may have
an alarm module connected. This means a maximum
of 16 modules per system (four on each door
controller, although only two on a Readykey K1200).

Each alarm module has 8 possible inputs. These are
numbered 1 to 8 on each alarm module. When
reporting, however, the zone number, 1 to 128, is
used. The zone number is as shown in the following
table.

Table 21: Zone Number

Zone Numbers

Input Number:

Location

1

2

3

4

5

6

7

8

Door Controller 1

Alarm Module 1

1

2

3

4

5

6

7

8

Alarm Module 2

9

10

11

12

13

14

15

16

Alarm Module 3 *

17

18

19

20

21

22

23

24

Alarm Module 4 *

25

26

27

28

29

30

31

32

Door Controller 2

Alarm  Module  5

33

34

35

36

37

38

39

40

Alarm  Module  6

41

42

43

44

45

46

47

48

Alarm  Module  7  *

49

50

51

52

53

54

55

56

Alarm  Module  8  *

57

58

59

60

61

62

63

64

Door Controller 3

Alarm Module 9

65

66

67

68

69

70

71

72

Alarm Module 10

73

74

75

76

77

78

79

80

Alarm Module 11 *

81

82

83

84

85

86

87

88

Alarm Module 12 *

89

90

91

92

93

94

95

96

Door Controller 4

Alarm Module 13

97

98

99

100

101

102

103

104

Alarm Module 14

105

106

107

108

109

110

111

112

Alarm Module 15 *

113

114

115

116

117

118

119

120

Alarm Module 16 *

121

122

123

124

125

126

127

128

* Not available on Readykey K1200

Содержание K2200 Series































































Отзывы: