MAINTENANCE PROCEDURES
This section includes instructions for
basic maintenance procedures.
WARNING
Turn off the engine and follow
these
maintenance
procedures
when performing maintenance.
If you do not follow proper main-
tenance procedures you can be
injured by hot parts, moving parts,
electricity, chemicals or other haz-
ards.
WARNING
Should removal of a locking device
(e.g. lock tabs, self-locking fasten-
ers, etc.) be required, always re-
place with a new one.
NOTICE
Never leave any object,
rag, tool, etc., in the engine com-
partment or in the bilge.
Engine Oil
Recommended Engine Oil
Use XPS 4-STROKE SYNTH. BLEND
OIL (P/N 293 600 121).
NOTICE
Rotax engines have been
developed and validated using XPS
synthetic blend oil.
BRP recom-
mends the use of its XPS engine
oil at all times. If the recommended
XPS engine oil is not available, use
a 10W40 motorcycle oil compatible
with wet clutches and meeting both
requirements for API service classi-
fication SL, SJ, SM or SN and JASO
MA2 classification. Do not add any
additives to the recommended oil.
Damage caused by oil which is not
suitable for the engine may not be
covered by the BRP limited war-
ranty.
Engine Oil Level
NOTICE
Operating
the
engine
with an improper level may severely
damage engine.
CAUTION
Many components
in the engine compartment may be
very hot. Direct contact may result
in skin burn.
Oil level can be checked with water-
craft either in or out of water.
If Watercraft is Out of the Water
NOTICE
Watercraft must be level.
CAUTION
When operating the
engine while the watercraft is out of
water, the heat exchanger in the ride
plate may become very hot. Avoid
any contact with the ride plate as
burns may occur.
1. Raise trailer tow pole, then block in
position when bumper rail is level.
2. Install a garden hose on the exhaust
system flushing connector. Refer
to
EXHAUST SYSTEM
in this sec-
tion and follow the procedure.
NOTICE
– Never run engine without supply-
ing water to the exhaust system.
Failure to cool exhaust system
may severely damage it.
– Never run engine longer than
2 minutes. Drive line seal has no
cooling when watercraft is out of
water.
3. Remove the seats.
4. With the engine already at normal
operating condition, let engine
idle
for 30 seconds
then stop engine.
5. Wait at least 30 seconds for the oil
to settle in the engine, then pull dip-
stick out and wipe clean.
120
______________
Содержание Sea-Doo GTX
