Bolin Technology VCC-7 Series Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 57

background image

47

Firmware Upgrade

There are 4 types of firmware with this camera can be upgradable. The latest camera firmware is available to
be downloaded from Bolin website: www.bolintechnology.com.

1. MCU (Micro Control Unit) firmware upgrade via USB

2. IP encoder firmware upgrade via IP network

3. FPGA firmware upgrade via IP network

4. Resolution FHD to 4K firmware via IP network.

NOTE:

The firmware upgrade process is intended to be performed under the supervision of a BOLIN-Authorized
repair technician. For assistance with this, please contact your authorized BOLIN Technology dealer, installer,
or integrator. BOLIN Technology Technical Support can also be reached for assistance with this process

Upgrading MCU Firmware

MCU Firmware can be upgraded by following these steps:

1.

Load the .bin file onto a flash drive (Formatted as
FAT32), and name the file “HD20.bin”

2.

With the camera powered off, insert the flash drive to
the USB port on the back panel of the camera

3.

Apply power to the camera

The green indicator light above the lens will turn red for a few
seconds while the upgrade takes place. Once the upgrade is
finished, the light will turn green, and the camera will proceed
through a normal boot cycle. Check the data on the OSD boot
screen

Upgrading IP encoder firmware

You can upgrade camera IP encoder module Firmware via IP network.
Connect and configure your camera with your local network successfully, log in the camera IP web interface,
go to System, Maintenance section to upgrade the firmware.
How to make Firmware upgrade for IP Encoder, please refer to User Manual Part Two.

«
...
45
46
47
48
49
...
»

Содержание VCC-7 Series


























































Отзывы:

Нет отзывов

Похожие инструкции для VCC-7 Series

Бренд: Canon Страницы: 3

Бренд: Abode Страницы: 5

Бренд: jablotron Страницы: 16

Бренд: SAFERA Страницы: 15

Бренд: Godox Страницы: 14

Бренд: Edimax Страницы: 2

APO-SUMMICRON-M 50 mm f/2 ASPH.

Бренд: Leica Страницы: 8

Бренд: PNI Страницы: 20

Бренд: safer guard Страницы: 7

Бренд: FLIR Страницы: 2

Бренд: Revo Страницы: 7

Бренд: jablotron Страницы: 2

Бренд: ADEMCO Страницы: 40

Бренд: Black Страницы: 24

Бренд: Sercomm Страницы: 73

Бренд: EISST Страницы: 15

Бренд: Yashica Страницы: 28

IMI SENSORS Y683A101001

Бренд: PCB Piezotronics Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды