BMR SFU 0303 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 62

background image

52

SFU 0303

Frequenzumrichter

14

General Hints

Our frequency converters are highly valuable precision devices. Please take care of them with the
necessary attention, to preserve their high precision, high power ability, and long lifetime.

These devices leave our company only after a quality test and a full load check have been carried out.
Before mounting and use, please read the attached manual carefully and pay attention to the points
listed below.

✓

Before first activation of the device, verify, if it is in a faultless condition. If it was damaged during
shipping and transportation it must not be switched on.

✓

During installation the safety regulations have to be observed.

✓

Before the device is turned on for the first time, it should be verified, that the connected parts cannot
carry out uncontrolled movements.

✓

The frequency converter must not be operated close to heating devices or magnets or devices
generating strong magnetic fields.

✓

The maximum permissible ambient temperature of this device is from +41 °F till +104 °F.

✓

Sufficient air circulation around the converter should be ensured

✓

Fluids should be prevented from intruding into the housing. If it seems to be happened, the converter
has to be switched off immediately.

✓

The relative humidity must not exceed 90% (not condensed).

✓

The ambient air must not use aggressive, flammable or electrically conductive substances and should
be as free of dust as possible.

✓

All repairs and maintenance on the converter and the relating accessories must be carried out by
skilled personal and with powered off, only. To ensure this, the mains plug should be pulled out. In
doing this, both the terms of regulations for preventing accidents and the general and national rules
for mounting and safety have to be applied.

✓

The device must not be operated without properly connected PE connection and it has to be verified
that the mains connector is fixed with screws, if detachable.

Our common hints can give only a rough guideline because it is not possible for

BMR

GmbH

to cover all specific situations. The compliance with limits of EMC demanded by law

is the responsibility of the manufacturer of the unit or the machine. By doing controls and
tests in our laboratory or in delegated test-laboratories, BMR takes care, that our products
comply with the corresponding standards, in case they are installed appropriately.

«
...
50
51
52
53
54
...
»

Содержание SFU 0303































































Отзывы:

Нет отзывов

Похожие инструкции для SFU 0303

Бренд: 3onedata Страницы: 3

Бренд: Xantrex Страницы: 78

Бренд: Xanter Страницы: 54

Бренд: OST Страницы: 2

OmniConverter GPoE+/S

Бренд: OST Страницы: 10

BLUESTREAM DA44AU

Бренд: Dante Страницы: 12

Бренд: Magtek Страницы: 54

I/O SYSTEM FIELD 765-2704/200-000

Бренд: WAGO Страницы: 42

Бренд: PBI Страницы: 31

Бренд: Caen Страницы: 17

Бренд: I.D. AL Страницы: 26

Бренд: Waversasystems Страницы: 15

PURE SINEWAVE PS3000-12

Бренд: Samlex Europe Страницы: 2

Бренд: MPP Solar Страницы: 4

DASNET-SPLITTER

Бренд: D.A.S. Страницы: 12

Бренд: Digitus Страницы: 6

Бренд: SIIG Страницы: 12

Бренд: Vacon Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды