Blue Seal Turbofan E32M Скачать руководство пользователя страница 8

Страница: 8 / 48

-8-

Revision 1/F3586

Water Connection

• A cold water supply should be fitted to the

water inlet (¾” BSP hose connection)
which is located on the rear of the right
hand side of the unit.

•

Alternately, a connection elbow and

sealing washer is supplied with this unit
for direct connection of a ½” ID hose, and
is recommended for easy installation and
service.

• Connect water supply - Max inlet pressure

80psi / 550kPa.

• Turn on water supply to check for leaks.

Before Connection to Power Supply

• Remove all packing.
• Check equipment and parts for damage.

Report any damage immediately to the
carrier and distributor.

• Remove protective plastic coating from

the side panels.

• Check that the following parts have been

supplied with your oven:

4 x Foot assembly
4 x Oven racks
1 x Water inlet elbow (c/w washer)

• Report any deficiencies to the distributor

who supplied the oven.

• Fit the feet to the oven.
• Check that the available power supply is

correct to that shown on the rating plate
located on the right -hand side panel.

     208-220 V AC, 50 Hz, 28.8 A, 6.0 kW
     208 V AC, 60 Hz, 28.8 A, 6.0 kW
     230-240 V AC, 50 Hz, 27.8 A, 6.7 kW
     220-240 V AC, 60 Hz, 27.8 A, 6.7 kW

Location

• To ensure correct ventilation for the motor

and controls the following minimum

installation clearances are to be adhered
to:

Rear     40mm / 1½”
Left-hand side   40mm / 1½”
Right-hand side*   40mm / 1½”
Top   390mm / 16”
*   Fixed  installations  require  at  least

500mm (20”) clearance at the right
hand side for service accessibility.

• Position the oven in its working position.

2. INSTALLATION

IMPORTANT:

THE OVEN VENT

LOCATED ON THE CABINET TOP
MUST NEVER BE OBSTRUCTED.

WARNING: THIS APPLIANCE MUST BE GROUNDED.

floor mounting or provided with stands are
adjustable and will require adjusting in
levelling the unit.

• The unit should be positioned such that

the operating panel and oven shelves are
easily reachable for loading and
unloading.

Electrical Connection

• Remove right hand side panel to allow

access to the terminal block and strain
relief cable clamp.

• The cable can be fitted through the small

grommet and held by the cable clamp.

•

Connect cable to the terminals as
marked.

• Refit cover panel.

IMPORTANT:

MAXIMUM INLET WATER

PRESSURE IS 550 kPa / 80 psi.

WARNING: ALL INSTALLATION AND SERVICE REPAIR WORK MUST BE CARRIED
OUT BY QUALIFIED PERSONS ONLY.

Figure 2.1

Ground

Phase

Neutral

RED

BROWN

BLACK

GREEN/YELLOW

GREEN

WARNING:

THIS APPLIANCE MUST

BE GROUNDED / EARTHED

BLACK

BLUE

WHITE

• Use a spirit level to ensure oven is level

from side to side and front to back. (If this
is not carried out, uneven cooking could
occur). The feet/legs used with bench/

Содержание Turbofan E32M

















































Результаты поиска

Содержание Turbofan E32M

Отзывы:

Blue Seal Turbofan E32M, Руководство по обслуживанию, Страница: 8 / 48

Результаты поиска

Содержание Turbofan E32M

Отзывы: