Blue Seal Turbofan E32M Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 48

Blue Seal Turbofan E32M Скачать руководство пользователя страница 29

-29-

Revision 1/F3586

6.3.12 WATER SOLENOID

5) Withdraw old thermostat phial through

side of oven. Note position in phial
bracket.

6) Insert new thermostat.
7) Re-assemble in reverse order.

NOTE:

Ensure that the thermostat phials are

located in their correct positions. The
main thermostat probe must be on the
side closest to the door. The hold
thermostat must be on the side closest to
the fan and elements.

1) Ensure water supply is turned off.
2) To access the solenoid, remove the right

hand service panel (refer 6.2.2)

3) Disconnect all water connections from the

water solenoid.

4)

Remove water solenoid from oven by

removing two screws securing the water
solenoid to its mounting bracket.

Figure 6.3.14

6.3.11 HEATING CONTACTOR

1)

Remove the right hand service panel

(refer 6.2.2).

2) Unclip contactor from the gear plate.

Figure 6.3.13

3) Clip new contactor onto gear plate.
4) Transfer wires from old contactor to new

contactor, ensuring all wires are in their
correct positions.

Contactor

Control thermostat

phial

Hold thermostat

phial

Towards

the

door

Figure 6.3.11

Two screws

6.3.10 HOLD THERMOSTAT

1) Open control panel (refer 6.2.1) and undo

two screws securing hold thermostat
bracket.

2) Remove the two screws securing the hold

thermostat to the bracket, and then fit the
new thermostat in its place.

3) Transfer wires to new thermostat.
3) Open oven door, remove racks and fan

baffle rack. Loosen the thermostat phial
bracket (refer figure 6.3.10).

Figure 6.3.12

4) Withdraw the old hold thermostat phial

through the side of the oven. Note the
position of the phial in the bracket.

5) Insert new thermostat phial.
6) Re-assemble in reverse order.

NOTE:

Ensure that the thermostat phials are

located in their correct positions. The
main thermostat probe must be on the
side closest to the door. The hold

Water

solenoid

«
...
27
28
29
30
31
...
»

Содержание Turbofan E32M

















































Отзывы:

Нет отзывов