manualshive.com logo in svg

Blue Seal Turbofan E32M, Руководство по обслуживанию, Страница: 23 / 48

Поделиться
Скачать
Blue Seal Turbofan E32M Скачать руководство пользователя страница 23

-23- 

Revision 1/F3586 

Timer not switching on buzzer 

With timer in zero position, check voltage to 
top connection (terminal one) and bottom  
connection (terminal two) of timer.  If there is 
no voltage at terminal one then check wiring. 
If no voltage at terminal two then timer is 
faulty—replace. 
NOTE:  Timer  will  continue  to  run                 
approximately three minutes below zero. 

 

Buzzer and time up indicator will continue until 
the timer is manually switched off (to vertical 
position). 

6.1.9  NO HEAT 

No power to thermostat 

Check  voltage  to  terminal  2  on  oven           
thermostat.  If there is no voltage then check 
voltage through terminal 5 and one on hold 
relay (behind control panel).  If there is no 
voltage to terminal 5 then check wiring.  If 
there is no voltage to terminal 1 then check 
that the hold relay has no power at relay coil 
terminal 7.  If relay coil is not energised (ie no 
power at 7) and no power out of terminal 1, 
then the relay is faulty—replace. 

6.1.8   60 MINUTE TIMER NO TIME UP       

INDICATOR 

Indicator faulty 

With the timer in the zero position, check for 
voltage across the indicator light.  If correct, 
then the indicator light is faulty—replace. 
If there is no voltage then check wiring. 

Thermostat faulty 

Set thermostat to 200°C or 400°F.  Check the 
voltage out of terminal 1 on the thermostat.  If 
there is no voltage then the thermostat is 
faulty—replace. 
If the voltage is correct and the heating light is 
on then check all wiring to heating contactor. 
 

Heating contactor faulty

 

With thermostat on, check that the heating 
contactor coil has power to terminal A1 and 
voltage across the coil, terminals A1 and A2.  
If incorrect check wiring. 
If voltage is correct, check that contactor pulls 
in and closes the contacts when power to  
contactor coil is on.  Correct operation will 
make an audible noise when closing contacts 
and on the front face of the contactor the  
contact mechanism will visibly pull in.  If not, 
contactor is faulty—replace. 
If contactor operates correctly, check for  
continuity through the poles of the contactor 
when closed.  If no continuity through 

 

connected poles then contacts are blown and 
contactor requires replacing. 

If relay is energised (ie power at 7) then 
’Roast n Hold’ switch is on and unit is in hold 
mode.  Turn off ’Roast n Hold’ and recheck 
operation. 

NOTE:   

There should be no voltage across 

these terminals when ‘Roast ‘n Hold’ is not 
selected. 

Figure 6.1.5 

7 

5 

3 

1 

8 

4 

Hold Relay 

Terminal A1 

Terminal 3 

Terminal 2 

Terminal A2 

Terminal 1 

Terminal 4 

Figure 6.1.7 

For checking elements where temperature 
overrun is occurring, check that contactor  
releases (opens) when thermostat is switched 
OFF.  If not, contacts of the contactor have 
welded shut and elements will be ON and 
heating will be continuous.  Contactor is 
faulty—replace. 
 

1

2

3

5 7

4 6 8

Figure 6.1.6 

Hold Relay 

Содержание Turbofan E32M

















































Отзывы:

Нет отзывов