Blue Seal Turbofan E32M Скачать руководство пользователя страница 17

Страница: 17 / 48

-17-

Revision 1/F3586

FAULT

POSSIBLE CAUSE

REMEDY

SLOW RECOVERY

Oven in ‘Roast ‘n Hold’ mode.

Overloading of oven.

Electrical supply incorrect.

Fan not working.

Thermostat out of calibration.

(Refer fault diagnosis 6.1.11)

Element not working.

Switch off ‘Roast ‘n Hold’.

Reduce oven loading.

Check supply voltage is as per
rating plate voltage.

Check fan operation.

Correct calibration.

(Refer service section 6.4.1)

Correct element fault.

(Refer Fault: No Heat)

ELEMENT NOT WORKING

Element faulty (blown).

(Refer fault diagnosis 6.1.9)

Replace.

(Refer service section 6.3.15)

NO THERMOSTAT HEATING
INDICATOR

Indicator faulty.

(Refer fault diagnosis 6.1.12)

Replace.

(Refer service section 6.3.3)

ROAST TIMER (180 MINUTE)
WILL NOT TIME DOWN

NO HOLD INDICATOR

HOLDING TEMPERATURE
INCORRECT

Roast ’n’ Hold switch not de-
pressed.

No power to timer / timer faulty..

(Refer fault diagnosis 6.1.13)

‘Roast ‘n Hold’ switch faulty.

(Refer fault diagnosis 6.1.13)

Faulty indicator.

(Refer fault diagnosis 6.1.14)

Faulty timer.

(Refer fault diagnosis 6.1.14)

Hold thermostat set tempera-
ture incorrect.

Hold thermostat faulty.

(Refer fault diagnosis 6.1.15)

Depress switch. Switch will
illuminate.

Correct electrical fault / replace
timer.

(Refer service section 6.3.8)

Replace.

(Refer service section 6.3.4)

Replace.

(Refer service section 6.3.3)

Replace.

(Refer service section 6.3.8)

Adjust to correct temperature.

(Refer service section 6.4.5)

Replace.

(Refer service section 6.3.10)

DOOR DOES NOT CLOSE

Tray in way of door.

Door seal obstruction.

Door handle installed
incorrectly.

Door catch setting incorrect.

Door pivot bushes / pins worn.

Correctly position tray in rack.

Correctly install door seal.

(Refer service section 6.3.22)

Ensure handle is fitted correctly.

Adjust.

(Refer service section 6.4.3)

Replace.

(Refer service section 6.3.23)

Содержание Turbofan E32M

















































Результаты поиска

Содержание Turbofan E32M

Отзывы:

Blue Seal Turbofan E32M, Руководство по обслуживанию, Страница: 17 / 48

Результаты поиска

Содержание Turbofan E32M

Отзывы: