manualshive.com logo in svg

Blue Seal Turbofan E32M, Руководство по обслуживанию, Страница: 16 / 48

Поделиться
Скачать
Blue Seal Turbofan E32M Скачать руководство пользователя страница 16

-16- 

Revision 1/F3586 

FAULT 

POSSIBLE CAUSE 

REMEDY 

NO WATER INJECTION / 
STEAM 

Water not turned on. 
 
Oven water nozzle blocked. 
 
 
Fault with water valve. 

(Refer fault diagnosis 6.1.5) 

 
 
Steam switch faulty. 

Turn water on at water supply. 
 
Remove, clean or replace.  

(Refer service section 6.3.14)

 

 
Service or replace as required. 

(Refer service section 6.3.12, 
6.3.13) 

 
Replace. 

(Refer service section 6.3.4)

 

CONTINUOUS WATER OUT 
OF OVEN WATER NOZZLE 

With oven on only—Electrical 
fault. 

(Refer fault diagnosis 6.1.6) 
 

With oven on or off - water 
valve faulty or requires  
cleaning.

 

Correct electrical fault. 
 
 
 
Service or replace as required. 

(Refer service section 6.3.12, 
6.3.13)

 

60 MINUTE TIMER WILL NOT 
TIME DOWN 
 
60 MINUTE TIMER  
INACCURATE BELOW 20 
MINUTES 
 
 
 
 
 
60 MINUTE TIMER NO TIME 
UP BUZZER 
 
 
 
 
60 MINUTE TIMER NO TIME 
UP INDICATOR 

Timer faulty. 
 
 
Timer not set correctly. 

 
 

 
 
Zero (time up) position not set 
correctly. 

 

Buzzer faulty. 

(Refer fault diagnosis 6.1.7) 
 

Timer not switching on buzzer. 

(Refer fault diagnosis 6.1.7) 

 
Indicator faulty. 

(Refer fault diagnosis 6.1.8) 

Replace. 

(Refer service section 6.3.7) 

 
For timer settings below 20  
minutes, always rotate past 20 
minutes, then back to desired 
time. 

 
(Refer service section 6.4.6) 

 

 

Replace. 

(Refer service section 6.3.5) 
 

Replace. 

(Refer service section 6.3.7) 

 
Replace. 

(Refer service section 6.3.3) 

NO HEAT 

No power to thermostat. 

(Refer fault diagnosis 6.1.9)

 

 
Thermostat faulty. 

(Refer fault diagnosis 6.1.9) 
 

Heating contactor faulty. 

(Refer fault diagnosis 6.1.9) 

 
Element faulty (blown). 

(Refer fault diagnosis 6.1.9) 

Identify fault and correct. 
 

 

Replace. 

(Refer service section 6.3.9) 

 
Replace. 

(Refer service section 6.3.11) 
 

Replace. 

(Refer service section 6.3.15) 

NO TEMPERATURE         
CONTROL (TEMPERATURE 
OVERRUN) 

Heating contactor faulty. 

(Refer fault diagnosis 6.1.9) 

 
Thermostat faulty. 

(Refer fault diagnosis 6.1.10)

 

Replace. 

(Refer service section 6.3.11) 

 
Replace. 

(Refer service section 6.3.9)

 

Содержание Turbofan E32M

















































Отзывы:

Нет отзывов