manualshive.com logo in svg

Blue Seal Turbofan E32M, Руководство по обслуживанию, Страница: 30 / 48

Поделиться
Скачать
Blue Seal Turbofan E32M Скачать руководство пользователя страница 30

-30- 

Revision 1/F3586 

6.3.15  ELEMENTS 

6.3.14  SPRAY NOZZLE 

5)   Carefully withdraw solenoid. 
6)   Replace or service solenoid as required. 
7)   To reinstall, reverse procedure. 
8)   Check water connections do not leak. 
9)  Check for correct operation of the oven 

water injection. 

1)   Inside the oven remove the RH side fan 

baffle, then unscrew the spray nozzle. 

1)   Remove service panel (refer 6.2.2) and 

baffle. 

2)    Remove the wires from the elements. 

Figure 6.3.15 

Figure 6.3.18 

Spray nozzle 

2)   Clean or replace as required, ensuring 

debris free on re-assembly. 

3)   Ensure that the spray nozzle is installed in 

the vertical position. 

2)   Unscrew the elements from inside the 

oven. 

6.3.13  WATER SOLENOID CLEANING 

1)   Disconnect water supply from the water 

solenoid. 

2)   Remove the sieve from the water valve 

assembly by pulling firmly away from the 
assembly with a pair of pliers. 

Sieve 

4)   Clean the sieve, removing all dirt and 

grime. 

5) 

  Replace the sieve and reconnect the  

water supply. 

Figure 6.3.16 

Figure 6.3.17 

Element 

wires 

6.3.16  FAN 

1)   With baffle removed  undo the grub screw 

securing the fan to the motor shaft. 

2)   Remove the fan from the shaft, replace, 

and reassemble. 

Figure 6.3.19 

Grub screw 

Element screw 

3) 

 

 

Pull elements carefully to remove. 

 

 

Silicone sealant may require effort to  
remove elements. 

4) 

 

 Replace and re-assemble in reverse 

 

order.  Use high temperature (232°C / 
450°F minimum) RTV silicone sealant to 
seal element against side wall of oven. 

Element Rating: 
208-220 V     Inner Element         17.0 ohms 
                      Outer Element        14.1 ohms 
230-240 V     Inner Element         19.4 ohms 
                      Outer Element        17.0 ohms 

Содержание Turbofan E32M

















































Отзывы:

Нет отзывов