Blue Seal Turbofan E32M Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 48

Blue Seal Turbofan E32M Скачать руководство пользователя страница 12

-12-

Revision 1/F3586

the control panel. When the relay is switched
ON a normally closed switch pole on the relay
is opened and the normal power supply to the
oven thermostat is isolated. A second

normally open switch pole is closed and this
provides power to the 3 hour roast timer.

If the roast timer is in the Hold (vertical)
position the timer switch contacts will be in
their normally closed position and supply
power directly to the Hold thermostat located
behind  the  control  panel.    The  Hold
thermostat is factory set to 75°C (167°F) and
will supply power to the heating elements
through the heating contactor as required to
maintain its preset temperature.

The thermostat heating light will also cycle
On/Off  as  the  Hold  thermostat  maintains
temperature.

In the Roast-and Hold mode the 3 hour timer
can be set to a selected roasting time. During
this time period the normally open switch
contacts of the timer are closed. The timer
has two change over switches and in this
position one is used to supply power to its
timing motor and the other is used to switch
power directly to the main oven thermostat.
During the 3 hour timer run-down period the
oven temperature will be controlled by the
main oven thermostat to the set temperature
and operate as previously described.

When the 3 hour timer has run down and
reached the Hold position the two switch
contacts change over to their normally closed
position which isolates power from the timer
motor and the oven thermostat. It also
switches  power  back  to  the  oven  hold
thermostat. At this point the temperature
control  is  now  maintained  by  the  hold
thermostat as previously described. To

cancel the hold circuit the Roast-and-Hold
switch is turned Off. This turns off the
contactor which removes power from the 3
hour timer and closes the contactor pole on
the contactor that feeds the main oven

thermostat. The Hold indicator light above the
3 Hour timer will illuminate whenever the oven
is operating in hold mode (Roast ‘n Hold se-
lected, and 3 Hour timer at zero position).

The factory preset hold thermostat can be
adjusted as required to change the holding
temperature if necessary. Refer Service
section for this procedure.

The following Troubleshooting Guide should
be  used  to  identify  any  incorrect  oven
operation.  On correct identification of the
operating fault the Troubleshooting Guide will
make  reference  to  the  corrective  action
required, or refer to the Fault Diagnosis
section and/or Service section to assist in
correction of the fault.

«
...
10
11
12
13
14
...
»

Содержание Turbofan E32M

















































Отзывы:

Нет отзывов