Blue Seal Turbofan E32M Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 48

Blue Seal Turbofan E32M Скачать руководство пользователя страница 35

-35-

Revision 1/F3586

6.4.4 DOOR ROLLER CATCH
ADJUSTMENT

1) Open the door.
2) Remove the two screws securing the

roller catch to the door and withdraw the
catch.

3) Tighten or loosen the nuts on the catch

assembly to adjust the height of the roller.

4) Refit catch to door and check operation.

Adjust again if necessary.

Figure 6.4.8

6.4.7 60 MINUTE TIMER ZERO POSITION

ADJUSTMENT

1) Remove 60 minute timer knob by pulling it

firmly away from control panel.

2) Open control panel (refer 6.2.1). Loosen

two screws on control panel holding 60
minute timer.

3) The timer can now be rotated a small

amount to ensure that the buzzer sounds
and indicator illuminates at the zero (time
up) position.

6.4.5 DOOR ALIGNMENT

1)

Loosen the five screws along the

bottom edge of the oven front.

Figure 6.4.6

2) Adjust the door position to ensure that it is

square with the oven. Tighten the screws.

Figure 6.4.5

Two screws

Roller catch

Adjustment nuts

Five screws

5) If necessary the roller catches can be

removed from the door (after removing
handle on stainless steel doors) to adjust
height settings for correction of door catch
operation.

6.4.6 HOLD TEMPERATURE ADJUSTMENT

1) Open control panel (refer 6.2.1) to gain

access to the hold thermostat (located
inside the control panel).

2) The hold temperature of the oven can be

adjusted by turning the hold thermostat
dial to the desired hold temperature.

Hold
thermostat

Figure 6.4.7

«
...
33
34
35
36
37
...
»

Содержание Turbofan E32M

















































Отзывы:

Нет отзывов