Blackrock Microsystems NeuroPort Скачать руководство пользователя страница 36

Страница: 36 / 74

Revision 1.00 / LB-1070 – NeuroPort Biopotential Signal Processing System IFU
© 2021 Blackrock Microsystems, LLC

Digital Output: Timed

A digital output in timed mode will send a pulse train with specified parameters.

The signal can be configured by setting frequency and duty cycle, or samples

high and low.

Frequency (Hz)

: The number of pulses per second.

Duty Cycle

: The percentage of time a pulse train is high.

Samples High

: Number of 30kHz sample periods output should be held high.

Samples Low

: Number of 30kHz sample periods output should be held low.

Offset (mV)

: DC offset voltage of the digital output.

Digital Output: Triggered

A digital output in triggered mode will send a pulse when the selected trigger

stimulus occurs.

Digital Input Rising Edge

: Waveform triggers when a user defined digital input

pin transitions from low to high. A digital input bit must be selected.

Digital Input Falling Edge

: Waveform triggers when a user defined digital input

pin transitions from high to low. A digital input bit must be selected.

Spike Unit

: Waveform triggers when a sorted unit is detected on a defined

channel.

NeuroMotive ROI

: Waveform triggers when a subject enters or exits a region of

interest.

Extension

: Waveform triggers based on custom extension code loaded onto

hardware.

Serial I/O

The Serial I/O Properties window

displays the serial communication

parameters and allows the user to

name and enable the serial port.

Serial communication parameters

cannot be changed.

Figure 23–Serial I/O

Содержание NeuroPort











































































Результаты поиска

Содержание NeuroPort

Отзывы:

Похожие инструкции для NeuroPort

Бренды по названию

Популярные бренды

Blackrock Microsystems NeuroPort, Инструкция по эксплуатации

Результаты поиска

Содержание NeuroPort

Отзывы:

Похожие инструкции для NeuroPort

Бренды по названию

Популярные бренды