Blackrock Microsystems NeuroPort Скачать руководство пользователя страница 31

Страница: 31 / 74

Revision 1.00 / LB-1070 – NeuroPort Biopotential Signal Processing System IFU
© 2021 Blackrock Microsystems, LLC

Raw Data

: Record raw data stream before filtering or sorting is applied.

AC Input Coupling

: High pass filter to remove DC offset.

Software Reference Selection

: Apply software referencing to local field

potential or both Local field potential and spike data.

Reference Electrode

: Select channel to use as software reference.

Enable Spike Processing

: Allow detection of spike events on channel.

Filter

: Filter selection for spike event processing.

Graphical Chooser

: Allows visualization of the spike processing filter in place.

Threshold Value

: Voltage threshold for classification of a spike event in mV.

RMS Threshold

: Set parameters for auto-threshold calculation.

Sorting Algorithm

: Set the sorting algorithm for a channel as described in Spike

Sorting on Page 38.

Enable Amplitude Rejection

: Rejects waveforms exceeding a specified

amplitude.

Upper/Lower Limit (uV)

: Voltage limits for amplitude rejection.

Figure 18– Filter Properties

Содержание NeuroPort











































































Результаты поиска

Содержание NeuroPort

Отзывы:

Похожие инструкции для NeuroPort

Бренды по названию

Популярные бренды

Blackrock Microsystems NeuroPort, Инструкция по эксплуатации

Результаты поиска

Содержание NeuroPort

Отзывы:

Похожие инструкции для NeuroPort

Бренды по названию

Популярные бренды