Black+Decker BCD701, Руководство пользователя

Страница: 7 / 80

nickel metal hydride or lithium-ion batteries
in the trash or municipal solid waste stream
and the Call 2 Recycle® program provides an
environmentally conscious alternative. Call 2
Recycle, Inc., in cooperation with
BLACK+DECKER and other battery users,
has established the program in the United
States and Canada to facilitate the
collection of spent nickel cadmium, nickel
metal hydride or lithium-ion batteries. Help
protect our environment and conserve
natural resources by returning the spent
nickel cadmium, nickel metal hydride or
lithium-ion batteries to an authorized
BLACK+DECKER service center or to your
local retailer for recycling. You may also
contact your local recycling center for
information on where to drop off the spent
battery. RBRC® is a registered trademark of
Call 2 Recycle, Inc.
Important Charging Notes
1. Longest life and best performance can
be obtained if the battery pack is
charged when the air temperature is
between 65 °F – 75 °F (18 ° – 24 °C). DO
NOT charge the battery pack in an air
temperature below 40 °F (4.5 °C), or
above 104 °F (40 °C). This is important
and will prevent serious damage to the
battery pack.
2. If the battery pack does not charge
properly:
a. Check operation of receptacle by
plugging in a lamp or other appliance;
b. Check to see if receptacle is connected
to a light switch which turns power off
when you turn out the lights;
c. Move the power adapter and battery
pack to a location where the surrounding
air temperature is approximately 65 °F –
75 °F (18 ° – 24 °C);
d. If charging problems persist, take the
tool, battery pack and USB cable to your
local service center.
3. The battery pack should be recharged
when it fails to produce sufficient power
on jobs which were easily done
previously. DO NOT CONTINUE to use
under these conditions. Follow the
charging procedure. You may also charge
a partially used pack whenever you
desire with no adverse effect on the
battery pack.
Transportation
Warning : Fire hazard. Do not store
or carry the battery pack so that
metal objects can contact exposed
battery terminals. For example, do
not place the battery pack in aprons,
pockets, tool boxes, product kit boxes,
drawers, etc., with loose nails, screws, keys,
etc. Transporting batteries can possibly
cause fires if the battery terminals
inadvertently come in contact with
conductive materials such as keys, coins,
hand tools and the like. The US Department
of Transportation Hazardous Material
Regulations (HMR) actually prohibit
transporting batteries in commerce or on
airplanes in carry-on baggage UNLESS they
are properly protected from short circuits.
So when transporting individual battery
packs, make sure that the battery terminals
are protected and well insulated from
materials that could contact them and cause
a short circuit.
Caution : GoPak battery terminal cap should
be used when battery is not connected to a
power tool. Terminal cap is provided for use
whenever the battery is out of the tool.
Remove cap before placing battery into tool.
FCC requirements for all digital
devices
This device complies with Part 15 of the FCC
Rules and Industry Canada License-exempt
RSS standard(s). Operation is subject to the
following two conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any interference
received, including interference that may
cause undesired operation.
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's authority
to operate the equipment.
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
7
ENGLISH
(Original instructions)