Black Box LPB201A Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 182

background image

4.4 PoE

4.4.1 POE S

TATUS

Table 4-14 shows all the parameters of the PoE status.

Table 4-14 PoE screen options.

Parameter Description

PoE Status

Display the information about the PoE status.

Vmain

The volt is supplied by the PoE.

Imain

The sum of the current that every port supplies.

Pconsume

The sum of the power that every port supplies

Power Limit

The maximal power that the switch can supply (Read Only).

Temperature

The temperature of the chip on PoE

Port No

Port number.

Port On

Show whether the port is supplying the power to the PD or not

AC Disconnect Port Off

Port is turned off due to the AC Disconnect function.

DC Disconnect Port Off

Port is turned off due to the DC Disconnect function.

Overload Port Off

The switch will stop supplying the power to the port due to the power
required by the PD that is linked to the port on the switch excesses
the Class setting of the PD

Short Circuit Port Off

The switch will stop supplying the power to the port if it detects that
the PD linked to the port is short circuit.

Over Temp. Protection

The port of the switch will be disabled due to fast transient rise in
temperature to 240

o

C or slow rise in temperature to 200

o

C.

Power Management Port Off

Due to total power required by all PDs linked to the switch excesses
the power limit, so the switch stops supplying the power to this port
after referring to the information of the priority.

24-Port 10/100BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports

48

«
...
49
50
51
52
53
...
»

Содержание LPB201A























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPB201A

Бренд: JDS Uniphase Страницы: 37

IP-Reach IPR-M1

Бренд: Raritan Страницы: 4

Бренд: Vega Страницы: 44

Бренд: TAXON TOOLS Страницы: 9

Бренд: Black Box Страницы: 10

TGS-1080-M12 Series

Бренд: ORiNG Страницы: 2

Бренд: cable matters Страницы: 12

Бренд: Lantech Страницы: 29

Бренд: TRENDnet Страницы: 2

Бренд: Lindy Страницы: 54

Бренд: Opengear Страницы: 109

Бренд: SMART-AVI Страницы: 9

iConverter GX/X

Бренд: Omnitron Systems Technology Страницы: 2

Бренд: Rosewill Страницы: 10

SME-8M-xxx-24V series

Бренд: Festo Страницы: 2

Бренд: N-Tron Страницы: 2

Бренд: Rukra Страницы: 3

CoreBuilder 7000

Бренд: 3Com Страницы: 516

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды