Black Box LPB201A Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 182

background image

Table 4-43 (continued). Parameter Setting screen options.

Parameter Description

max. Request (1-10)

The maximum of number times that the authenticator will retransmit
an EAP Request to the supplicant before it times out the
authentication session. The valid range: 1 – 10.

Default: 2 times

suppTimeout (1-65535 s)

A timeout condition in the exchange between the authenticator and
the supplicant. The valid range: 1 –65535.

Default: 30 seconds

serverTimeout (1-65535 s)

A timeout condition in the exchange between the authenticator and
the authentication server. The valid range: 1 –65535.

Default: 30 seconds

4.14 Alarm Configuration

4.14.1 E

VENTS

C

ONFIGURATION

The Trap Events Configuration function is used to enable the switch to send out the trap information while
pre-defined trap events occurred. The switch offers 22 different trap events to users for switch management. The
trap information can be sent out in three ways, including email, mobile phone SMS (short message system) and
trap. The message will be sent while users tick (

;

) the trap event individually on the web page shown as below.

Table 4-44. Events Configuration screen options.

Parameter Description

Trap

Cold Start, Warm Start, Link Down, Link Up, Authentication

Failure, User login, User logout

STP

STP Topology Changed, STP Disabled, STP Enabled

LACP

LACP Disabled, LACP Enabled, LACP Member Added, LACP Port
Failure

GVRP

GVRP Disabled, GVRP Enabled

VLAN

Port-based VLAN Enabled, Tag-based VLAN Enabled

Module Swap

Module Inserted, Module Removed, Dual Media Swapped

PoE PoE

Failure

24-Port 10/100BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports

80

«
...
81
82
83
84
85
...
»

Содержание LPB201A























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPB201A

Бренд: D-Link Страницы: 357

Бренд: Barco Страницы: 6

Бренд: Zamel Страницы: 2

FlowPoint 2100 12

Бренд: Cabletron Systems Страницы: 36

Бренд: Hawking Страницы: 2

UltraHD Switch 3:1

Бренд: Oehlbach Страницы: 20

Бренд: Kramer Страницы: 2

24-Port Gigabit Switch

Бренд: Belkin Страницы: 2

Бренд: Black Box Страницы: 2

Бренд: Labgear Страницы: 8

Бренд: Black Box Страницы: 2

Бренд: DANLERS Страницы: 2

Бренд: NVision Страницы: 92

Бренд: Extron electronics Страницы: 6

Бренд: ATEN Страницы: 15

Бренд: Tripp Lite Страницы: 9

Бренд: TP-Link Страницы: 2

Бренд: Unipoe Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды