Black Box LPB201A Скачать руководство пользователя страница 75

Страница: 75 / 182

4.12.2 A

GGREGATOR

IEW

To display the current port trunking information from the aggregator point of view.

Table 4-36. Aggregator View screen options.

Parameter Description

Aggregator

It shows the aggregator ID (from 1 to 26) of every port. In fact, every
port is also an aggregator, and its own aggregator ID is the same as
its own Port No.

Method

Show the method a port uses to aggregate with other ports.

Member Ports

Show all member ports of an aggregator (port).

Ready Ports

Show only the ready member ports within an aggregator (port).

This page shows the detailed information of the LACP trunking group

Table 4-37. LACP Detail screen options.

Parameter Description

Actor

The switch you are watching on.

Partner

The peer system from this aggregator’s view.

System Priority

Show the System Priority part of a system ID.

MAC Address

Show the MAC Address part of a system ID.

Port

Show the port number part of an LACP port ID.

Key

Show the key value of the aggregator. The key value is determined
by the LACP protocol entity and can’t be set through management.

Trunk Status

Show the trunk status of a single member port. --- means not ready.

24-Port 10/100BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports

Содержание LPB201A






















































































































































































Результаты поиска

Содержание LPB201A

Отзывы:

Похожие инструкции для LPB201A

Бренды по названию

Популярные бренды

Black Box LPB201A, Руководство пользователя

Результаты поиска

Содержание LPB201A

Отзывы:

Похожие инструкции для LPB201A

Бренды по названию

Популярные бренды