background image

14

(3) LCD display:

 A "Supertwist" liquid crystal 

display (LCD) meter allows display of readings, 
messages, and other information. 

(4) Alarm lights:

 Four LED (light emitting diode) 

alarm lights provide a visual indication of alarm 
state.  Each light is dedicated to a single 
channel of detection, and will emit a bright red 
light when a sensor alarm level is exceeded.  
One of the alarm light assemblies also includes 
a photo-sensor used to monitor the level of 
background illumination.  An automatically-
activated backlight brightens the meter display 
whenever the instrument is taken into a dark 
area. 

(5)  On / Off "mode" button:

 The large black push-

button is called the "mode" button.  It is used to 
turn the PhD Ultra on and off and to control 
most other operations, including the automatic 
calibration adjustment. 

(6)  Sensor compartment cover:

 The sensors are 

protected by a vented sensor compartment 
cover.  Its own protective filter cap individually 
protects each sensor.  A water-resistant PVC 
gasket and inner-liner protect the instrument 
against leakage or exposure to liquids.  

(7)  Audible alarm orifice:

 A cylindrical orifice 

extending through the sensor compartment 
cover houses the audible alarm.  The waterproof 
audible alarm seats directly to the PVC inner-
liner to protect the instrument against leakage or 
exposure to liquids. 

(8) Battery pack:

 Two types of interchangeable 

battery packs (rechargeable NiCad and 
disposable alkaline) are available for use in the 
PhD Ultra.  NiCad battery packs may be 
recharged while the pack is installed in the 
instrument, or the battery pack may be removed 
from the instrument and recharged separately. 

Chapter 2 of the PhD Ultra owner's manual 
covers battery replacement and charging 
procedures. 

(9)  Battery charger connector: 

A water-resistant 

connector at the rear of the case is used to 
connect the PhD Ultra to the “drop in” style PhD 
Ultra fast charger. 

(10) Bottom 

surface:

 A sturdy clip allows the 

user to wear the PhD Ultra on a belt or other 
article of clothing.  Snaps are provided to hold 
the PhD Ultra securely in the padded leather 
weather cover. 

(11) Key 

pad:

 The key pad is located on the 

back of the PhD Ultra under the belt clip.  Slide 
the belt clip towards the rear of the instrument to 
access the four small push-buttons.  The key 
pad consists of, four buttons labeled  “+”, “-”, 
“CAL”, and "ALM”.  These buttons are normally 
only used during set-up and other programming 
procedures.   

Use of these push buttons is reserved for 
authorized personnel.

1.11  PhD Ultra accessories 

Each PhD Ultra is delivered in a foam lined box 
containing the PhD Ultra detector, padded leather 
weather cover, carrying strap, sample draw / 
calibration adopter, hand-aspirated sample-draw kit 
(with 10 feet of sample draw tubing), 2 feet of 
additional tubing for use during calibration, 
reference manual, quick reference card, and 
comprehensive training video. 

The sample draw kit comprises a slip-on sample 
draw / calibration adapter, squeeze bulb, sample 
probe, replacement sample probe filters, and ten 
feet of tubing. 

1.11.1  “Alkaline” PhD Ultra detectors   

If the PhD Ultra has been purchased as an “alkaline” 
instrument the standard accessories also include an 
alkaline battery pack and a set of 3 disposable AA 
alkaline batteries. 

1.11.2  “NiCad” PhD Ultra detectors   

If the PhD Ultra has been purchased as a “NiCad” 
instrument the standard accessories additionally 
include a NiCad battery pack, slip in PhD Ultra fast 
charger, as well as a spare alkaline battery pack and 
set of disposable batteries. 

1.11  PhD Ultra kits 

PhD Ultra detectors may also be purchased as part 
of complete kits.   

1.11.1  PhD Ultra Confined Space Kits 

Besides the standard accessories included with 
every PhD Ultra, Confined Space Kits also include 
calibration fittings, regulator, one cylinder of each of 
the appropriate calibration gases and foam lined 
waterproof carrying case for the instrument, 
calibration materials and other accessories.

 

Cylinders used in Confined Space Kits contain 
either 58 or 103 liters depending on the specific 
mixture of gas. 

1.11.2  PhD Ultra Value Packs 

It is also possible to order the PhD Ultra configured 
as a “Value Pack”.  The Value Pack comprises an 
alkaline PhD Ultra, all standard accessories, 34 liter 
cylinder of all-in-one calibration gas, fixed flow rate 
regulator, and foam lined carrying case.

 

Содержание PhD Ultra





























































Отзывы: