Bilanciai D70E Скачать руководство пользователя

Страница: 32 / 88

1-32

D70E

Here is a list of these symbols and their meanings:

Weight stable symbol

Indicates that the weight value displayed is stable and
thus may be printed and/or transmitted.

Weight stable symbol

Indicates that the weight value displayed is stable
and thus may be printed and/or transmitted.

Centre zero symbol

Indicates that the weight on the scale is near to
zero i.e. within -1/4 + 1/4 of a division.

Tare symbol

Indicates that there is a tare symbol memorized by
acquisition.

Tare symbol entered via the keyboard Indicates
that the tare value acquired has been digitized via
the keyboard.

Gross weight symbol

Net weight symbol

When the indication is on, this means that the tare
has been memorised by acquisition.

If the

indication is on at the same time, this

means that the tare has been entered via the
keyboard.

Weighing range indication for multi-extension

(ME) instruments

Unit of measurement of the displayed weight

If the indication flashes, this means that the
weight is within the minimum weighing
range.

Содержание D70E

























































































Результаты поиска

Содержание D70E

Отзывы:

Похожие инструкции для D70E

Бренды по названию

Популярные бренды

Bilanciai D70E, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание D70E

Отзывы:

Похожие инструкции для D70E

Бренды по названию

Популярные бренды