BIG BALE Transtacker Extra Скачать руководство пользователя

Страница: 31 / 36

8.0

Maintenance

WARNING:

Be careful to support raised mechanisms that

may fall when hydraulic connections are undone. This is

particularly applicable to a partially raised platform, side and

rear clamps, forks, table lift, table retract and raised

pickups. If in doubt, contact your local Big Bale Transtacker

agent.

WARNING:
Before Commencing Any Repairs / Maintenance

Shut off engine, remove ignition key, and unplug electric box

before performing any maintenance or repair work.

8.1

Service Schedule

Daily or 10 Hrs

Weekly or 50 Hrs

Annual

Grease the complete pickup assembly
(18 points)
Remove any build up of crop

Check hoses for scuffing and leaks.

Check clamp side safety pins.

Grease table components. (7 points)

Grease tip pivots. (6 points)

Grease clamp pivots (14 points)

Wax oil extension bearings and slide
section
Oil fork rollers. (18)

Oil beam pulleys. (8)

Oil tensioner pulleys. (2 x 4 + 2)

Check for visible structural damage.

Check cylinder seals for leakage.

Check tyre pressures.

Check wheel nuts are tight.

Check for any leaks in hydraulic lines,
valves or cylinders.
Check plugs and sockets for corrosion.
(Keep clean)
Check junction box for loose
connections and corrosion.
Check cables and connectors for
damage.
Check sensors for damage.

Replace or clean the pressure line
filter element.
Grease cables and inspect for damage
or wear
Check ring hitch for excessive wear.

Check brakes for function and
adjustment.
Inspect tyres for damage and wear.

Fig. 90

Содержание Transtacker Extra





































Результаты поиска

Содержание Transtacker Extra

Отзывы:

Похожие инструкции для Transtacker Extra

Бренды по названию

Популярные бренды

BIG BALE Transtacker Extra, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Transtacker Extra

Отзывы:

Похожие инструкции для Transtacker Extra

Бренды по названию

Популярные бренды