background image

5.0

Operation

5.1

Attachment to the Tractor

Drawbar 

Requirements

The drawbar is normally supplied with a ring hitch, which is

suitable for connection to the pickup hitch found on most

tractors in the UK.   

Ensure that your tractor hitch is suitable for this type and

dimension of ring.   

Ensure the capacity is a minimum of 3 Tonnes. Additionally,

the recommended minimum horsepower is 140 HP and 6

Tonnes weight.   

An oil supply of at least 60 L/min @ 200 bar (8.79

Gallons/min (UK) @ 2900 psi) and a minimum electric

supply of 20 Amps @ 12v DC are required. The tractor must

be fitted with a power beyond unit.

Attaching 

Hitch the tractor to the machine. Remove and store the

drawbar stand and pin. The machine should now sit

approximately level at the chassis.   

Turn the tractor cautiously and ensure the tractor links etc

do not foul on any part of the machine and that there is

sufficient clearance for hoses etc. Remove links if

necessary.

Connect the brakes to the tractor and ensure correct

operation.

Release the hand brake 

(Fig. 7)

, which is under the front

left of the chassis, and obtain assistance to check the

operation of the trailer brake cylinders when the brake pedal

is depressed. 

Ensure the tractor lighting voltage is 12 v DC before

connecting the lights. 

Connect the lights via the 7-pin plug stored just off centre of

the service post and confirm correct operation.

Tractor connections and identification colours are as follows;

(Fig. 8)

Hose 2 – Pressure – Red - 3/4” Hose

Hose 3 – Return – Blue – 1” Hose

Hose 4 – Load Sense – Yellow – 1/4” Hose

Hose 5 – Pilot drain – Blue- 1/4” Hose

For tractors with only three connections available hoses 3 &

5 may be joined together using a tee piece at the tractor

end.  

Please ensure that the above connections to the tractor’s

power beyond unit are made in accordance with your

Tractor Manufacturers instructions and Guidelines.  

9

Fig. 7

Tank

Blue

No. 5

1/4” Hose

No. 3

1” Hose

No. 1

3/4” Hose

No. 4

1/4” Hose

Tank

Pressure

Load Sense

Blue

Red

Yellow

No. 2  3/4” Hose

F1
10
Micron

Fig. 8

WARNING:

Oil under pressure can penetrate skin. Seek

medical advice involving any incident where this may occur.

Oil is an irritant. Wear protective gloves when handling.

CAUTION:

Ensure the tractor will supply at least 60 L/min

@ 200 bar (8.79 Gallons/min (UK) @ 2900 psi and does not

exceed 80 L/min (17.6 Gallons/min (UK)).  

Set the flow at 40-50 L/min. (8.79 - 11.0 Gallons/min (UK)).

5.2

Hydraulics

Содержание Transtacker Extra





































Отзывы: